OK, so I am assuming that your board containing com3 and com4 is using the standard IRQ. This would mean:
1. Radio, CW, and one rotor are all trying to use same IRQ4 ( com1 and com3 share an IRQ ). 2. Rotor two is ok.. no IRQ3 conflicts. I would try putting your second rotor on Com4 instead of Com3. See if that helps any. This would result in radio and cw on Com1/IRQ4 rotor 1 on com2/IRQ3 rotor 2 on Com4/IRQ3 spare com3/IRQ4 ----- Original Message ----- From: "k6anp" <[EMAIL PROTECTED]> To: "Jack" <[EMAIL PROTECTED]>; <[email protected]> Sent: Sunday, April 27, 2003 11:48 PM Subject: Re: [DXBase] Com Port problems > Com 1 Radio control and CW keying > > Com 2 Rotor 1. It does not matter which one I select M2 or Yaseu, either > one of them will work. > > Com 3 and Com 4 are unassigned. I'm attempting to use one of them for rotor 2. > > I'm not running any other software except for my OS, Windows 98 > > I do not have a modem installed. I'm using DSL. > > The card for com 3 and 4 is a SIIG dual port serial card. Remember, this > arrangement/equipment works with DXbase 2002. The only time it fails is > when I upgrade to 2004. > > Len > > At 11:00 PM 4/27/2003 -0400, Jack wrote: > >Sounds like comport trouble to me. Please list the following: > > > >1. What is each comport being used for? > >2. What other software is running at same time as DXbase? > >3. Do you have a modem installed and if so, what comport is it assigned to? > > > >This will possibly help diagnose the conflicts. > > > >Regards, > >Courtney > > > >----- Original Message ----- > >From: "k6anp" <[EMAIL PROTECTED]> > >To: <[email protected]> > >Sent: Sunday, April 27, 2003 7:38 PM > >Subject: [DXBase] Com Port problems > > > > > > > I should have mentioned in my first message the rotor control works fine > >in > > > COM 1 & 2. However I need one com for the radio, and two coms for two > > > rotors. So, I need a minimum of three working com ports. The radio doe s > >the > > > same thing as the rotor, only works in com 1 & 2 in DXBase 2004. The radio > > > works in all com ports in DXBase2002. > > > > > > I recently upgraded from 2002 to 2004. The rotor control works fine in > > > 2002. When I attempt to rotate the ant in 2004, the program locks up. I've > > > double/triple checked the setting and they are exactly the same as in > >2002. > > > I have been using com4. I tried writelog using the same com port for rotor > > > control and it works fine. > > > I tried moving the rotor control to com3..The same problem, it works fine > > > in 2002 and not in 2004 everything locks up. I have two makes of rotors > >one > > > is M2 the other is Yaesu 1000sdx. I have the same problems regardless of > > > which rotor I attempt to use. Both of them work in 2002, none of them work > > > in2004 in com4 or com3. > > > I did and redid the DXB drive setup..no luck. When the program locksup I > > > have to do the Cntrl, Alt, del and get the "DXbase not responding" > >message. > > > > > > Anyone have some ideas or suggestions about this problem. > > > > > > Len, K6ANP > > > > > > > > > > > > --- StripMime Report -- processed MIME parts --- > > > multipart/alternative > > > text/plain (text body -- kept) > > > text/html > > > The reason this message is shown is because the post was in HTML > > > or had an attachment. Attachments are not allowed. To learn how > > > to post in Plain-Text go to: http://www.expita.com/nomime.html --- > > > _______________________________________________ > > > DXBase Reflector - Please visit us on the web at www.dxbase.com > > > - - - - - - - - - - - - - - - - - - - - - - - > > > To UNSUBSCRIBE please visit: > > > http://mailman.qth.net/mailman/listinfo/dxbase > > > > > > _______________________________________________ > DXBase Reflector - Please visit us on the web at www.dxbase.com > - - - - - - - - - - - - - - - - - - - - - - - > To UNSUBSCRIBE please visit: > http://mailman.qth.net/mailman/listinfo/dxbase
