Hi Larry
Computer control is on Com-1, CW is on LPT-1 and RigBlaster is on Com-7
(two serial port card from Byterunner). All other settings are as you
mention. I may try putting the computer control on Com-6 (the other serial
port via Byterunner) but I don't think it will make any difference. Don't
have any thing to loose, hi hi.
The main computer is linked to an IC-756pro and all programs work OK on
it.
Both computers are the same, Dell 2.4 XP.
If all options fail, I am going to delete DXBase2005 and do a new
install. Just don't understand why N1MM and DXLab programs work and DXBase
doesn't.
Going to take a ride up into the mountains and clear my head. Tks for
the information.
JV
-------Original Message-------
From: Larry Strasser
Date: 03/14/06 09:51:34
To: [email protected]
Subject: [Dxbase] IC706MKIIG
JV,
I am using DXBASE "2006" with my 706mkIIG.( The setings should be the
Same in DXBase 2005)
Does your computer have a "legacy" serial port or are you using a
USB/SERIAL adaptor?
Make sure you have the folowing checked or selected:
"Manufacturer" = ICOM.
"MODEL" = IC-706MKIIG.
"CTS" checked and "Connect HF Radio 1 Serial Interface" checked.
Make sure you have the correct "Comport" selected.
I am using the following parameters:
BAUDRATE = 1200
PARITY = NONE
WORD LENGHT =8
STOP BITS = 1
I have the IC-706MKIIG internal parameters selected for 1200 baud.
I am using 2 USB/SERIAL adaptors on my Dell laptop along with WINKEY.
I hope this helps.
73, Larry
DXCLUSTER DXC.K2LS.COM
Spots from NA zones 1-8 only.
______________________________________________________________
Dxbase mailing list
Home: http://mailman.qth.net/mailman/listinfo/dxbase
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
--
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.1.375 / Virus Database: 268.2.2/280 - Release Date: 3/13/2006
From [EMAIL PROTECTED] Tue Mar 14 10:27:20 2006
From: [EMAIL PROTECTED] (Larry Strasser)
Date: Tue Mar 14 10:29:15 2006
Subject: [Dxbase] Slow
Message-ID: <[EMAIL PROTECTED]>
I have tried much faster speeds and it does not seem to make any difference,
Am I missing something?
Thanks for any info.
Larry
From [EMAIL PROTECTED] Tue Mar 14 10:27:33 2006
From: [EMAIL PROTECTED] (JV)
Date: Tue Mar 14 10:29:56 2006
Subject: [Dxbase] IC706MKIIG
References: <[EMAIL PROTECTED]>
Message-ID: <[EMAIL PROTECTED]>
I have tried speeds up to 19200 and they do not work. The manual says
use 1200.
JV
-------Original Message-------
From: ve3wej
Date: 03/14/06 10:04:16
To: DXBase List
Subject: Re: [Dxbase] IC706MKIIG
Why so slow???
> I am using the following parameters:
> BAUDRATE = 1200
> PARITY = NONE
> WORD LENGHT =8
> STOP BITS = 1
From [EMAIL PROTECTED] Tue Mar 14 17:38:31 2006
From: [EMAIL PROTECTED] (Bob Main)
Date: Tue Mar 14 17:40:59 2006
Subject: [Dxbase] Wish List
Message-ID: <[EMAIL PROTECTED]>
It might be to late now and it might can be done already, but I would like
to see the Internet Cluster window to open automatically when I start
DXBase.
Bob
KB4CL
