JV, FYI, I have successfully run an IC-706MKII with DXB2005 and DXB2006. Not sure why yours is not working, but you don't mention your connections to the radio. Are you using the ACC jack on the back panel? On my 706MKII the ACC jack is a 13 pin connector which I couldn't find so I purchased Icom's overpriced OPC-599 conversion cable that breaks out into two ACC jacks for the various pin connections.
I must be the only guy in the world who uses LPT-1 on my computer to go to a printer! Since you have a RigBlaster, why are you taking CW off LPT-1? Why not just use the serial port connected to the RigBlaster to key the DTR line to the RigBlaster then feed the CW output to the radio? Anyway, just wanted to let you know it does work. Just have to find the magic button somewhere. Gary AL9A ----- Original Message ----- From: "JV" <[EMAIL PROTECTED]> To: <[email protected]>; "Larry Strasser" <[EMAIL PROTECTED]> Sent: March 14, 2006 6:24 AM Subject: Re: [Dxbase] IC706MKIIG > Hi Larry > Computer control is on Com-1, CW is on LPT-1 and RigBlaster is on Com-7 > (two serial port card from Byterunner). All other settings are as you > mention. I may try putting the computer control on Com-6 (the other serial > port via Byterunner) but I don't think it will make any difference. Don't > have any thing to loose, hi hi. > The main computer is linked to an IC-756pro and all programs work OK on > it. > Both computers are the same, Dell 2.4 XP. > If all options fail, I am going to delete DXBase2005 and do a new > install. Just don't understand why N1MM and DXLab programs work and DXBase > doesn't. > Going to take a ride up into the mountains and clear my head. Tks for > the information. > JV > > -------Original Message------- > > From: Larry Strasser > Date: 03/14/06 09:51:34 > To: [email protected] > Subject: [Dxbase] IC706MKIIG > > JV, > > I am using DXBASE "2006" with my 706mkIIG.( The setings should be the > Same in DXBase 2005) > > Does your computer have a "legacy" serial port or are you using a > USB/SERIAL adaptor? > > Make sure you have the folowing checked or selected: > > "Manufacturer" = ICOM. > "MODEL" = IC-706MKIIG. > "CTS" checked and "Connect HF Radio 1 Serial Interface" checked. > > Make sure you have the correct "Comport" selected. > > > I am using the following parameters: > BAUDRATE = 1200 > PARITY = NONE > WORD LENGHT =8 > STOP BITS = 1 > > I have the IC-706MKIIG internal parameters selected for 1200 baud. > > I am using 2 USB/SERIAL adaptors on my Dell laptop along with WINKEY. > > I hope this helps. > > 73, Larry > > DXCLUSTER DXC.K2LS.COM > Spots from NA zones 1-8 only. > > > > ______________________________________________________________ > Dxbase mailing list > Home: http://mailman.qth.net/mailman/listinfo/dxbase > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > > -- > No virus found in this incoming message. > Checked by AVG Free Edition. > Version: 7.1.375 / Virus Database: 268.2.2/280 - Release Date: 3/13/2006 > > ______________________________________________________________ > Dxbase mailing list > Home: http://mailman.qth.net/mailman/listinfo/dxbase > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] >
