Chen...glad you succeeded... I too have had that problem with ALL O/S... I remember my car giving me a lot of grief with all its read-outs, my buddy in California, who has a 745 variant said he had experienced the same, disconnected the battery, drank a cold beer, then rebooted the car & left the ignition on for 30 minutes & all was cool.... Same/same computers....if in doubt, shutdown for 5 min, then reboot....good luck... BR>Pete
-----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of chen xueqin Sent: Tuesday, September 20, 2005 7:26 AM To: [email protected] Subject: [ECI] Re: D-link DSL-200 Ver:A2 modem probrem in SuSe 9.3 Hi Gilles and Pete: Thanks for your kindly reply. The problem disppeared. To my supprise, input "eciadsl-start", OK, input "pppoe-start", it reported connected, OK too. Very good.The config setting is the same as before, the only thing I do is to wait a day and re-power the PC. So far so good. When it connect, ppp0 link is create with ipv4 address. But the dns server is not auto configed. I have manually edit /etc/resolv.conf, specifying the dns ip. Except this ,everything worked well. Thanks for free EciAdsl and PPPoE client. PS: I'm from China, am I the first one to report use EciAdsl successfully?:) 2005/9/18, Gilles Espinasse <[EMAIL PROTECTED]>: > > > > ----- Original Message ----- > From: "chen xueqin" <[EMAIL PROTECTED]> > To: "eci maillist" <[email protected] > > Sent: Saturday, September 17, 2005 5:12 PM > Subject: [ECI] D-link DSL-200 Ver:A2 modem probrem in SuSe 9.3 > > > > Hi folks: > > I want to use internet uder SuSe 9.3 linux box. I have a D-link > > DSL-200 > > Ver(A2) modem. > > This modem works well on WinXP with following config: > > Encapsulation - RFC 2516 PPPoE > > Modulate = Multimode > > > > I downloaded eciasl-usermode-0.11beta1 driver, config it in graphy > > user interface. > > Then use "eciadsl-start" command, it report connect ok, say waiting > > for tap0. > > When I use ifconfig -a to see all the interface, I found it says > > like > these > > > > tap0 Link encap:Ethernet HWaddr 00:FF:A5:69:2E:F6 > > inet6 addr: fe80::2ff:a5ff:fe69:2ef6/64 Scope:Link UP BROADCAST > > RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 > > overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 > > carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX > > bytes:308 (308.0 b) > > > > No inet4 addr, I think it's incorrect. > > > in bridged mode, the bridge don't need to have an ip address. > With PPPoE, this is ppp0 wich will receive the address supplied by the > ISP. > > > When I use route to see the route table, no route for tap0. > > > > So that's the problem, I can't use tcp/ip use tap0 interface. > > > you are not at the ip level in bridged mode > > > What's wrong? > > 1. I can't find Encapsulation - RFC 2516 PPPoE in eciadsl config, > > how to > set > > it accordingly? > > It has only 5 options > > VCM_RFC2364 > > LLC_RFC2364 > > LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS > > VCM_RFC_1483_BRIDGED_ETH > > LLC_RFC1483_ROUTED_IP > > VCM_RFC1483_ROUTED_IP > > So does the modulate config. > > > > RFC1483 was deprecated by RFC2516, RFC differences look minor. > You probably need LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS > > > 2. tap0 can be created , but no route via it? Why > > > you are not at the ip level in bridged mode pppd will set the route > later if defaultroute option is used. > > If you don't have an answer during PPPoE start, your problem probably > is adsl synchronization as it is a bit special with eciadsl. Try other > sync files. > Other troubles may be bad VPI/VCI value (same no answer) or bad > login/password (this time the message is authentification failure). > > > Gilles > > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > Driver Linux pour modem ECI ADSL USB: http://eciadsl.flashtux.org > Archives de cette liste de diffusion: http://liste.eci.free.fr Pour se > desinscrire: mailto: [EMAIL PROTECTED] > > > > > > > -- /* [EMAIL PROTECTED]: chen xueqin [EMAIL PROTECTED]: [EMAIL PROTECTED] [EMAIL PROTECTED]: http://robbie.blogchina.com */ =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- Driver Linux pour modem ECI ADSL USB: http://eciadsl.flashtux.org Archives de cette liste de diffusion: http://liste.eci.free.fr Pour se desinscrire: mailto:[EMAIL PROTECTED] -- No virus found in this incoming message. Checked by AVG Anti-Virus. Version: 7.0.344 / Virus Database: 267.11.1/104 - Release Date: 9/16/2005 -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.344 / Virus Database: 267.11.1/104 - Release Date: 9/16/2005 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- Driver Linux pour modem ECI ADSL USB: http://eciadsl.flashtux.org Archives de cette liste de diffusion: http://liste.eci.free.fr Pour se desinscrire: mailto:[EMAIL PROTECTED]
