Hi Aravindh, I see following difference between your working and non-working logs.
29 0000000A B N N 1 1 ASIX AX88772B Ethernet Driver 2.4.0 Fv(A881D567-6CB0-4EEE-8435-2E72D33E45B5)/FvFile(25DC8C52-544B-43BF-A58D-995F96DEB726) 2B 0000000A ? N N 0 0 ASIX AX88772B Ethernet Driver 2.4.0 Fv(A881D567-6CB0-4EEE-8435-2E72D33E45B5)/FvFile(25DC8C52-544B-43BF-A58D-995F96DEB726) Is this the particular NIC driver for your network card? I see the NIC card is managed by this driver in your working environment. Thanks, Ting -----Original Message----- From: Aravindhlal G.S.S [mailto:[email protected]] Sent: Monday, July 04, 2016 1:06 PM To: Ye, Ting <[email protected]>; [email protected] Subject: RE: Error. The protocol 'gEfiIp4ConfigProtocolGuid' was required and not found Hi Ting, I think it should be fine, because we have a similar setup and that is working fine. In the working setup, I could see many of the drivers whose type is not yet recognised. But in case of the working setup, almost many of the drivers are classified and they are being used by devices (entries under #D & #C). I have attached the output of drivers command of both working & non-working setups to differentiate it. Could you please take a look at these attached files ? Both of them are running the same version of EFI firmware. Am I missing anything big ? Thanks -Aravindh -----Original Message----- From: Ye, Ting [mailto:[email protected]] Sent: Monday, July 04, 2016 10:20 AM To: Aravindhlal G.S.S; [email protected] Subject: RE: Error. The protocol 'gEfiIp4ConfigProtocolGuid' was required and not found Hi Aravindh, It looks the problem is irrelevant to upper layer drivers including SNP, MNP, and others, but your UNDI driver does not manage your NIC card: F7 0000000A ? N N 0 0 UNDI32 Driver Fv(A881D567-6CB0-4EEE-8435-2E72D33E45B5)/FvFile(A1F436EA-A127-4EF8-957C-8048606FF670) Is the UNDI driver the correct NIC device driver in UEFI? Best Regards, Ting -----Original Message----- From: edk2-devel [mailto:[email protected]] On Behalf Of Aravindhlal G.S.S Sent: Monday, July 04, 2016 12:39 PM To: Aravindhlal G.S.S <[email protected]>; Ye, Ting <[email protected]>; [email protected] Subject: Re: [edk2] Error. The protocol 'gEfiIp4ConfigProtocolGuid' was required and not found Sorry, Forgot to attach file in previous email. Attached in this email. Hi Ting, The chipset being used is Puma 7 DOCSIS 3.1 chip. I could also see the UNDI driver installed. Please see below. F7 0000000A ? N N 0 0 UNDI32 Driver Fv(A881D567-6CB0-4EEE-8435-2E72D33E45B5)/FvFile(A1F436EA-A127-4EF8-957C-8048606FF670) Please see the attached text file the output of drivers command. I tried following, but none of them worked. * I reset all the parameters/values to defaults * I tried reconnecting all the drivers * I tried to unload and then again load the driver using the handle * I tried to bind all drivers to a specific devices and start the driver * I tried to force defaults on all devices using "drvcfg -f 0" command Could you please take a look in the attached text file ? Still am I missing any drivers to be installed ? is there any way to reinstall the drivers (SNP, MNP & other network drivers) ? Appreciate your help ! Thanks -Aravindh -----Original Message----- From: Ye, Ting [mailto:[email protected]] Sent: Monday, July 04, 2016 7:12 AM To: Aravindhlal G.S.S; [email protected] Subject: RE: Error. The protocol 'gEfiIp4ConfigProtocolGuid' was required and not found Hi Aravindh, Which platform are you using for running the network stack? You probably need a particular UNDI driver for your Ethernet card if you are not using simulator like NT32 platform. Best Regards, Ting -----Original Message----- From: edk2-devel [mailto:[email protected]] On Behalf Of Aravindhlal G.S.S Sent: Friday, July 01, 2016 6:42 PM To: [email protected] Subject: [edk2] Error. The protocol 'gEfiIp4ConfigProtocolGuid' was required and not found Hi Experts, I am not able to config the Ethernet interface in UEFI shell. I am running Shell> teractive Shell v2.1 EDK II UEFI v2.40 (EDK II, 0x00010000) The drivers commands list the required driver, but #D is 0 and Type is "?". Am I missing any drivers to be installed ? If so could you please help in sharing the pointers ? T Y C I P F A DRV VERSION E G G #D #C DRIVER NAME IMAGE PATH === ======== = = = === === =================================== ========== 97 0000000A ? N N 0 0 Simple Network Protocol Driver Fv(A881D567-6CB0-4EEE-8435-2E72D33E45B5)/FvFile(A2F436EA-A127-4EF8-957C-8048606FF670) 9C 0000000A ? N N 0 0 IP4 CONFIG Network Service Driver Fv(A881D567-6CB0-4EEE-8435-2E72D33E45B5)/FvFile(26841BDE-920A-4E7A-9FBE-637F477143A6) 9D 0000000A ? N N 0 0 IP4 Network Service Driver Fv(A881D567-6CB0-4EEE-8435-2E72D33E45B5)/FvFile(9FB1A1F3-3B71-4324-B39A-745CBB015FFF) Appreciate your help. Thanks -Aravindh _______________________________________________ edk2-devel mailing list [email protected] https://lists.01.org/mailman/listinfo/edk2-devel _______________________________________________ edk2-devel mailing list [email protected] https://lists.01.org/mailman/listinfo/edk2-devel _______________________________________________ edk2-devel mailing list [email protected] https://lists.01.org/mailman/listinfo/edk2-devel
