G'day, At the salt mine so not near #1400 at present.
How exactly do you determine that transmission has stopped? Does the receive unmute? On #1400 when I cross the QRP/QRO boundary level, in either direction, there isn't any unmuting and just for interest I set up as split and the TX frequency remained selected. I must confess that the one thing I didn't check for was modulation. I get the impression that the "feature" is subtle rather than gross. Will check again at the first opportunity. Regards, Mike VP8NO ----- Original Message ----- From: "S55M" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Thursday, January 20, 2005 8:45 PM Subject: Re: [Elecraft] K2 turning power behavior > OK.I will write it down agn step by step... > > > 1.Turn Power button to 0,1W (full left) > > 2.Press PTT > > 3.When on TX without releasing PTT turn power up over 10W limit to turn on > 100W PA. > > When i do this my K2 stops transmiting above the 10W point (when KPA100 > clicks up). > The only thing to do then is to release PTT and press it again and "voila" > on the AIR again. > > If i go in reverse direction (turning power from 100Wtts to less then 10W) > everything works fine! > > K2 Nr-3204 SW- 1.09 and 2.04 > > It's not a problem but must be a hint..... > > > S55M-Adi > > > ----- Original Message ----- > From: "Donald Nesbitt" <[EMAIL PROTECTED]> > To: "Michael Harris" <[EMAIL PROTECTED]>; "S55M" <[EMAIL PROTECTED]>; > <[email protected]> > Sent: Friday, January 21, 2005 12:00 AM > Subject: Re: [Elecraft] K2 turning power behavior > > > > Not on mine either. 73 --don n4hh K2/100/KAT100 #2028 > > ----- Original Message ----- > > From: "Michael Harris" <[EMAIL PROTECTED]> > > To: "S55M" <[EMAIL PROTECTED]>; <[email protected]> > > Sent: Thursday, January 20, 2005 5:22 PM > > Subject: Re: [Elecraft] K2 turning power behavior > > > > > > > G'day, > > > > > > <snipo> > > > So...if i press the PTT (dot line on keyer when on USB) without talking > > > (or maybe also with ssb modulation because i did not test it) and turn > the > > > power button on 100W and then reduce the power back to minimum my K2 > stops > > > transmitting.I must then release the PTT and press it again to go into > TX > > > mode. > > > Is this happening with all K2's? > > > <snipo> > > > > > > Not on #1400 (external KPA100/KAT100 combo) unless I've read the above > > > incorrectly. > > > > > > Regards, > > > > > > Mike VP8NO > > > > > > > > -- > > No virus found in this outgoing message. > > Checked by AVG Anti-Virus. > > Version: 7.0.300 / Virus Database: 265.7.1 - Release Date: 1/19/05 > > > > _______________________________________________ > Elecraft mailing list > Post to: [email protected] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > _______________________________________________ Elecraft mailing list Post to: [email protected] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
