I have a crimper and will redo them today. Right after I put a phase inverter on my 6m stack. So many projects, so little time.
Need to get these things done before the baby comes. he is due in on Tuesday. Thanks, Keith AG6AZ -----Original Message----- From: Eugene Balinski Sent: Sunday, July 29, 2012 9:34 AM To: Keith Heimbold ; [email protected] Cc: [email protected] Subject: Re: [Elecraft] K3 transmit audio cuts out APP connectors can be a real pain if not done absolutely correctly. I ended up purchasing a ratcheting crimper from HRO as I could never get just the right force on the manual one. It was either too weak and the wire would fall out when tugged, or I would mash it too hard, and the contact would not fit in to the plastic housing. The ratcheting crimper is first time, every time, at least for now 73 K1NR On Sun, 29 Jul 2012 06:54:23 -0700 Keith Heimbold <[email protected]> wrote: > Don, > > I am pretty sure that we found the culprit. The APP > connectors did not click properly for the one set and I > am examining the ones for the other. I will need to be > more diligent in making sure I get a good click inserting > into the plastic housing. > > I spent a lot of time rooting out any RFI issues but I > guess that is really time well spent since cleaning up my > shack and all the cables and wires is probably a good > idea. > > Thanks, > > Keith > AG6AZ > > Sent from my iPhone please excuse typos > > On Jul 29, 2012, at 6:34 AM, "Don Wilhelm" > <[email protected]> wrote: > > > Keith, > > > > If your APP connectors do not mate with a bit of a > *click*, then they are assembled incorrectly. The blades > of the conductors *must* be locked over the tips of the > spring fingers located in the housing. > > > > Things come in threes so the sayings go, I have > repaired 2 KPA100s in the last week which did not have > the blades of the APP connector fully seated - I am > waiting on the 3rd one. > > > > 73, > > Don W3FPR > > > > On 7/28/2012 11:10 PM, Keith Heimbold wrote: > >> Don, > >> > >> I am now starting to think that it is an issue with my > power connectors that I am using. > >> > >> I bought some additional ferrites and put the balun > design 1113u in line to take care of RFI but i know > believe that the power connectors are a little > intermittent at times. I don't always get a solid click > when inserting into the back of the K3 or into the power > supply line. I like the convenience of those type of > connectors but they do seem to loosen up over time. > >> > >> Thanks again, > >> > >> Keith > >> AG6AZ > >> > >> Sent from my iPhone please excuse typos > >> > >> On Jul 28, 2012, at 3:44 PM, "Don Wilhelm" > <[email protected]> wrote: > >> > >>> Keith, > >>> > >>> You could also have a loose connection in your > microphone cable. When operating SSB, if there is no > audio, there will be no RF output. > >>> So you can look at the PTT, the audio, the power > supply, and just about every thing else in your station. > Cables are usually the weak link. > >>> > >>> 73, > >>> Don W3FPR > >>> > >>> On 7/28/2012 5:34 PM, Keith Heimbold wrote: > >>>> Gene, > >>>> > >>>> Great suggestion. It maybe the connector going into > the rig or the connectors which I built. > >>>> > >>>> Thanks, > >>>> > >>>> Keith > >>>> AG6AZ > >>>> > >>>> > >> > ______________________________________________________________ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:[email protected] > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: > http://www.qsl.net/donate.html > >> > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: > http://www.qsl.net/donate.html --------------------------------------------------------------------- Web mail provided by NuNet, Inc. The Premier National provider. http://www.nni.com/ ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
