Your U-Verse router settings are set to not respond to ping request, you could change the settings in the router to respond to ping request.
73, Michael - N8NOC K1-4 #3046 K3/10 #6596 KX3 #1573 On Dec 19, 2013, at 9:45 AM, bwru...@gmail.com wrote: It works. No idea why, but this morning everything is good, though I still can't ping my MD address from inside my FL network. Begin forwarded message: > From: "bwru...@gmail.com" <bwru...@gmail.com> > Date: December 19, 2013 at 9:27:04 AM EST > To: Elecraft Reflector <elecraft@mailman.qth.net> > Subject: Fwd: K3/0 to K3 RemoteRig issue > > OK guys. Don't waste time on this. The problem is definitely the router. > > I cannot successfully ping my remote router in Maryland (where the remote K3 > is) from inside my network here in Key West. I CAN successfully ping it when > I am using Verizon with my iPad. I CAN ping anything else I try from inside > the network. > > Something in the way the router setup is working is preventing some kinds of > data from flowing back to me. This was not the case before AT&T's technician > set up the static ip addresses. > > The router is a Motorola NVG510 used by the ATT U-Verse system. On-line, I > find many forum threads dealing with idiosyncratic behavior of this > particular router. That is what zapped me. Now I have to work out a fix. > > Tnx. Happy Holidays. > > 73, > > Brian > > -- > 70 is the new 40. > > Brian F. Wruble, C.F.A. > 1107 Key Plaza, PMB 447 Key West, FL 33040 > Summers: P.O.Box 57, 7400 Augustine Herman Highway, Georgetown, MD 21930 > eFax 305.768.0278 Skype bwruble > > > Begin forwarded message: > >> From: "Brian F. Wruble" <bwru...@gmail.com> >> Date: December 18, 2013 at 6:13:28 PM EST >> To: Elecraft Reflector <elecraft@mailman.qth.net> >> Subject: K3/0 to K3 RemoteRig issue >> Reply-To: bwru...@gmail.com >> >> Hi all: >> >> I have had my remote operation working beautifully, with just problems >> figuring out CW and Digital, but slowly getting there. Sideband has been >> fine, and I am enjoying ham radio in Key West while operating through my >> station on Maryland's Eastern Shore. >> >> Then... I turned on the K3/0 a couple hours ago. I heard the sounds of 40M >> SSB, where I had my most recent QSO. But the dial shows 21.000.00 and mode >> shown is CW. I can tune, and obviously the distant K3 is tuning, as I can >> hear the signals change. I can change bands, change modes, go in and out of >> XMIT. The front panel of the K3/0 never shows a change, just sits there. >> >> One possible clue: I had an AT&T internet tech in today to give me a static >> ip (external ip) to support my surveillance system. That has not affected >> any internet functions --- I have email, browser, and comms with the K3. I >> just don't have feedback from the K3. It seems to me that if I have good >> internet, then the K3/0 and RemoteRig shouldn't care about the changes, but >> it is suspiciously coincidental. ........ > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html