Hello Dick, That could be done but I would have to manually turn the sub Rx on to do this, if I am to hear both. Hearing is not mandatory but it is an asset. And more, it is somewhat disconcerting to use P3 marker A to affect the K3's VFO "B" receiver and, P3 marker B with the K3s VFO "A" receiver. It just seems intuitive that the P3 MKR A should be identified with the K3 VFO A and it's unnecessary mental juggling to do it backwards.
I know when I use my spot log in my logging program to select a desired station and frequency, it automatically selects the Sub Rx "B" in the K3 to go split and be ready to transmit properly assuming that data was included in the comments section. It seems intuitive for the MKR B to not only move VFO "B" but to also put it in split. Since it does not, it seems to me its not doing its job yet. If that's the case, perhaps that's work for a future update or there's a setting in the K3 that has to be engaged that hasn't been done yet and that I haven't yet found. The mistakes I've been experiencing in the pileups have been because after selecting the magenta B to be on the desired place in the pileup to transmit so the DX hears me, I then forget to also go to the K3 and hold down the split button. I'm used to such changes being done automatically by my logging program. To me, it's the only reason to QSY VFO B when you need a split operation. Gary KA1J > Can you move the marker A green up and put the magenta b freq on the dx station? I've not used the P3 for this, but I normally use the 2nd Rx to listen to the DX station and move VFO A around in the pileup. I make fewer mistakes than when I try split. > > Dick, K6KR > > > > > On Mar 18, 2014, at 23:30, "Gary Smith" <[email protected]> wrote: > > > > Reading the P3 screen I see a station transmitting. I use Marker A > > (Green) to pin me on that desired station as soon as I tap the knob > > to QSY me to a desired signal. > > > > I listen to the station and they say UP so I know to hold in the MKR > > button to activate B ((Magenta) I see where the last transmission is > > and I place the Magenta marker at that location and tap: The Sub Rx > > goes to that frequency where the DX was last listening but sub is not > > engaged, it just sits on that frequency and does nothing with it. > > > > Problem is that if I don't then reach over and manually hold the > > split button on the K3 itself to have the K3 transmit on the DX > > listening frequency, I'll still keep transmitting on the DX transmit > > frequency because the K3 will not have gone split; its as if the > > procedure is halted half way and it shouldn't function this way, its > > not intuitive. > > > > If I'm going to the effort to engage Marker B to QSY its because I > > want to transmit on the Marker B frequency. What do I have to the do > > differently to force the K3 go split to transmit on the B freq when I > > tap on MKR B? > > > > Thanks, > > > > Gary > > KA1J > > > > --- > > This email is free from viruses and malware because avast! Antivirus > > protection is active. > > http://www.avast.com > > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to [email protected] > --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
