No, AGC on/off has no effect.
On 4 Dec 2014 17:00, Joe Subich, W4TV wrote:
The amplitude of this click depends on the amount of noise or signals
in the 'channel'. When listening to rx noise with no antenna, there's
no click. The worst case is a big pileup.
It would appear that the K3 is momentarily running at full gain when
returning from transmit, the "click" being full gain until the AGC can
react to signal levels 'in the channel'. That supposition can only be
confirmed by Lyle or Wayne but you might be able to moderate the click
by turning off AGC and riding the RF gain.
73,
... Joe, W4TV
On 2014-12-04 9:05 AM, Vic Rosenthal wrote:
Tommy,
I have 8 pole filters for 400, 1000 and 2800 Hz. I am almost always
using the 400 on CW. I use QRQ mode whenever possible. I found various
sources of clicks including bias switching in my amplifier, and a
switched power source for my Pixel Loop. I removed everything to
isolate the problem. All tests were done in TX TEST mode, no RF
generated.
The most bothersome K3 generated noise is a click when returning to
receive state. You hear it in full or semi- QSK mode when returning to
receive. The amplitude of this click depends on the amount of noise or
signals in the 'channel'. When listening to rx noise with no antenna,
there's no click. The worst case is a big pileup. There is also a
noise that is hard to describe, sort of a fuzziness around the
sidetone. That also depends on the amount of signal and noise in the
background.
Turning down either the audio or RF gain helps with both artifacts,
but makes the output lower than desirable.
I talked to Wayne and Lyle a long time ago about possible ways to
ameliorate these noises and they had some ideas, but I haven't heard
anything recently.
Vic 4X6GP/K2VCO
On Dec 4, 2014, at 3:22 PM, Chester Alderman
<[email protected]> wrote:
Hi Vic,
With interest, I read your emails about the K3 QSK and the noise it
produced and I have a question for you. I’ve had my K3 for about
three years and I purchased it with a full complement of CW filters
for both receivers, including the 8-pole 250 hz filter. I normally
run my radios in full QSK, but of course, depending on sending speed,
running the K3 in full QSK means you lose too many other good features.
I never really noticed the noise generated while in full QSK until
recently, and it is quite bad! About a year ago I changed my 8-pole
250 hz filter to the 5 pole 250 hz filter and actually I think that
is when I started noticing how bad the pumping and generated noise
from my K3 sounded. Of course I run AGC-Fast, with no preamp (unless
on 10m and then only seldom have the preamp turned on).
My question to you is do you have the 250 hz filter installed in the
main Rx and if so, is it the 8-pole or the 5-pole? I think right
after Christmas I am going to re-install my 8-pole filter just to see
if that has any bearing on the awful QSK noise.
Also, have you had any response from Elecraft on this issue?
Thanks for any comment Vic and 73,
Tom – W4BQF
--
73,
Vic, 4X6GP/K2VCO
Rehovot, Israel
http://www.qsl.net/k2vco/
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
