It appears to me that they are the same 16 macros, which are invoked via the buttons on the K-POD.
As I have many macros that I now invoke via software, I was hopeful that there might be a method by which I could have different 'macro sets', e.g. for SSB, RTTY, CW operation, contests, etc. I thought that perhaps saving a K3 configuration would also save the macro definitions, but this does not appear to be the case. I think that if the K3 Utility had the functions to allow saving and loading different user-defined 'macro sets', the utility of the K-POD would be enhanced. Just my $.02 worth ... - 73 and good DX de Mike, K6MKF, Past President - NCDXC > -----Original Message----- > From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of brian > Sent: Friday, July 08, 2016 9:34 AM > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] Now that the K-Pod is shipping, we could use your help > with useful macros > > Are these 16 macros in addition to above those previously available in firmware > to be assigned to various K3 buttons? > > 73 de Brian/K3KO > > > > On 7/8/2016 16:07 PM, Dick Dievendorff wrote: > > The most recent K3 Utility (1.16.26.5) stores 16 command macros in the K3. > > You can install it now from a link at the bottom of: > > http://www.elecraft.com/K3/k3_software.htm > > > > Command macros 1-8 correspond to K-Pod buttons F1-F8 Hold, Command > > macros > > 9-16 correspond to K-Pod buttons F1-F8 tap. > > > > 73 de Dick, K6KR > > > > > > -----Original Message----- > > From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of > > Matt Murphy > > Sent: Friday, July 8, 2016 08:50 > > To: Roger Marrotte <marro...@verizon.net> > > Cc: Elecraft Reflector <Elecraft@mailman.qth.net> > > Subject: Re: [Elecraft] Now that the K-Pod is shipping, we could use > > your help with useful macros > > > > Is there a specification of how the macros work with the knobs? I have > > not yet ordered a K-Pod, but would love to write some useful macros > > (especially for the knobs). Perhaps I could test the macros using the > > K3 terminal in the meantime but it would be great to know how the > > knobs are configured to trigger macros first. > > > > Advice appreciated. > > > > 73, > > Matt NQ6N > > > > On Fri, Jul 8, 2016 at 10:42 AM, Roger Marrotte <marro...@verizon.net> > > wrote: > > > >> Yes it does. It comes with two 6.8 ohm resistors. One 1/8 watt > >> leaded resistor and one 1/10 watt smd resistor. I did the mod with > >> the smd resistor. It's a small resistor about the size of a large > >> fruit fly and it goes kind of in a tight place, especially for a left > >> hander. I got it in and it works so I'm happy but if I had to do it > >> again I'd probably used the leaded resistor. I've done some smd work > before. > >> > >> Roger, W1EM > >> > >> -----Original Message----- > >> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of > >> Terry Schieler > >> Sent: Friday, July 08, 2016 10:56 AM > >> To: 'Wayne Burdick' <n...@elecraft.com>; 'Elecraft Reflector' > >> <elecraft@mailman.qth.net> > >> Subject: Re: [Elecraft] Now that the K-Pod is shipping, we could use > >> your help with useful macros > >> > >> Looks like my K-Pod should arrive tomorrow. Does it come with the DC > >> power modification resistors and mod instructions or do I need to > >> order > > those? > >> > >> 73, > >> > >> Terry, W0FM > >> > >> > _____________________________________________________________ > _ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:Elecraft@mailman.qth.net > >> > >> This list hosted by: http://www.qsl.net Please help support this > >> email > >> list: http://www.qsl.net/donate.html Message delivered to > >> m...@nq6n.com > >> > > > _____________________________________________________________ > _ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net Please help support this email > > list: http://www.qsl.net/donate.html Message delivered to > > d...@elecraft.com > > > > > _____________________________________________________________ > _ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net Please help support this email > > list: http://www.qsl.net/donate.html Message delivered to > > als...@comcast.net > > > _____________________________________________________________ > _ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html Message > delivered to mike.flow...@gmail.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com