Jim,
This involves primarily configuring the radio side router to forward the
correct UDP ports. It must be thoroughly tested before leaving the radio
site on its own.
I have a checklist setup that walks you through this process and will
forward it to you now in a separate mail.
73,
Mitch DJ0QN / K7DX
Mitch Wolfson DJØQN / K7DX
10285 Boca Cir, Naples, FL 34109
Skype: mitchwo
USA: Home:+1-239-221-9600 - Mobile:+1-424-288-9171
Germany: Home:+49 89 32152700 - Mobile:+49 172 8374436
On 29.10.2016 17:44, Jim Cary wrote:
John/Barry
Thanks for the quick responses. I’ll be setting up the other side tomorrow.
I think when I had them working at home I had both units connected before I
fired up the mini, so I didn’t have the problem.
73,
Jim
On Oct 29, 2016, at 5:39 PM, John <j...@eeek.org.uk> wrote:
Jim,
This is actually quite a simple one, luckily!
I'm assuming when you say RRC you mean the MicroHAM RemoteRig Control system -
I've helped set these up and test them for a couple of years now, so assuming
I've got that bit right...
It simply means that it's unable to talk to the other end (ie the kit you
haven't connected at the far end).
The MicroHAM RRC systems use SIP over UDP on three different ports - one for
voice data, one for CAT data, and one for control signals between the remote
head and the unit body. If it's a SIP connection error you're seeing, it's
because the two ends of the RRC system can't see each other (which, as you say,
is the correct case because you haven't hooked up the remote unit yet).
If I'm barking up the wrong tree, please correct me.
73, and a firm left handshake,
John (XLX)
-----Original Message-----
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jim Cary
Sent: 29 October 2016 22:27
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 Mini Error question
I just packed up both my control and remote systems and moved them down to my
ZF QTH, where they will be permanent.
I have the K3 mini hooked up to the control RRC unit, but haven’t hooked up the
remote unit yet/
When I powered up the mini, and turned the volume control I got a three tone
warning signal. The light over the aux/mic cable is flashing yellow, which
according to the Remote Rig manual means the SIP connection has failed…. but it
isn’t clear what that means or what to do about it. I’ve checked and doubled
checked all the connections and they look good.
Does anyone not in the CQ contest (!!!) have an idea?
Jim
W2SM
ZF2LC
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message
delivered to j...@eeek.org.uk
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to dj...@arrl.net
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com