I’ve had zero issues with WSJT-X over HRD and now that the logging hooks were added to HRD, no more importing logs (or a third party program to link logs) is required.
It just works. Rick WA6NHC Smell Czech correction happen > On Oct 1, 2018, at 12:42 PM, Bob McGraw K4TAX <[email protected]> wrote: > > While I use both WSJT-X, V1.9.1, and HRD, I allow WSJT to create and save > its own log. Then I transfer the entries from the WSJT log to my other log > system. That then uploads the selected entries to LOTW. I've more often > than not found that if I allow one software to run within or under another > software, there's just two many cooks in the kitchen tasting the pot. In > other words, I run WSJT as a stand a lone application and do not have any > conflicts. The operating system is a current version of Windows 10 with all > of their updates. > > As suggestions, I would open WSJT as a stand a lone and see if it connects to > the rig and operates correctly. Then close WSJT and open HRD using one of > its modes, i.e. PSK-31, and see if it operates correctly. If so on both, > and mine does, then there is no specific issue with either application or the > computer or the radio. I use the USB communication with my K3S. Then with > both applications running I find is the area where the hand shake is > supported to occur but indeed a fist fight breaks out. That says HRD will > need to be update in order for Windows 10 to handle the activity. The bottom > line, when Microsoft updates Windows 10, all other application software is > likely in need of an update as well. > > Good luck in resolving the issue. > > 73 > > Bob, K4TAX > > >> On 10/1/2018 12:36 PM, ROBERT MUELLER wrote: >> Mike, I would be interested in what you find. Since Microsoft and then HRD >> did upgrades I have not been able to get WSJT to work with HRD and my K3S, >> therefore, the logging from FT* to HRD will not work. When I try to set >> things up I get a message: Hamlib error: IO error while opening connection >> to rig. I am running a USB cable which worked fine until all the upgrades. >> Very interested in what you find. >> Bob, [email protected] >>> On October 1, 2018 at 11:49 AM Mike Greenway <[email protected]> wrote: >>> >>> >>> I have used for years a K3 on EME with WSJT using Line In/Out audio. >>> Recently got a K3S and I am now using USB (CODEC) audio in and out of the >>> radio. In WSJT-10 they have Rate In/Rate Out monitors that should normally >>> run at 1.000. Using the K3 analog audio these always stayed right on 1.000 >>> but now that I am using the USB audio they are jumping around quite often >>> and getting out of range indicated in WSJT with a red marker. I have tried >>> two different computers and the same result. I tried changing the sample >>> rate in the computer audio settings but no change in the problem. I plan >>> to go back to analog Line In/Out on the K3S unless someone has an idea on >>> how to settle down the Rate In/Out fluctuations. I have not found anything >>> in the K3S that might affect this. You can reply off line if you like. 73 >>> Mike K4PI >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:[email protected] >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to [email protected] >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [email protected] >> > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
