Good evening The Icom IC-7600 KAT500, and KPA500 are each grounded to a single
terminal strip with a #10 cable directly to a ground rod 15 ft away. The rod is
12 ft deep. Both the KAP and KTA were factory built as my soldering skills have
diminished since the Army training.
The IC7600 - In the back of the 7600 is a 4 conductor molex connector. The Icom
made cable splits into 2 connections on the KAT, the first is plugged into DC
power, and the second is plugged into the Tuner connection
- In the back of the 7600 is also a 7 conductor DIM connection (Acc2). I made a
cable to connect pin 3 to the KAT PTT RLY
The KAT - Other than mentioned above ant1 goes out to the antenna- XMTR is
connected via a 2 ft piece of LMR400 to the output of the KAP- The unlabeled
connector above the PTT RLY goes to the PA Key of the KAP
The KAP - Other than what is mentioned above the only other connection is a
piece of LMR400 from Ant1 on the 7600 to input on the KAP.
From: Jack Brindle <[email protected]>
To: "[email protected]" <[email protected]>
Cc: "[email protected]" <[email protected]>
Sent: Sunday, December 30, 2018 5:31 PM
Subject: Re: [Elecraft] KAT500/KPA500 with Icom 7600 accessory cable
Yeah, but we really want to get the problem solved so you can enjoy your KPA500
and KAT500 as much as we enjoy ours.That connection list will be most helpful
in this effort.
My thinking on the ground issue is that the power-plug ground is completing a
circuit that should not exist and thus disruptingoperations on band change. The
question would be what is connected to ground that should not be, and where?Are
the KPA and KATs kits or did they come assembled?
73!Jack, W6FB
On Dec 30, 2018, at 2:22 PM, Ken B <[email protected]> wrote:
Please allow me to clairify. Everyone deserves time off. I work 60 to 70 hrs
per week and appricate the down time
Sent from Yahoo Mail on Android
On Sun, Dec 30, 2018 at 5:07 PM, Jack Brindle<[email protected]> wrote:
The folks in Watsonville are taking a well deserved rest, but some of us are
still around. This sounds a lot like a grounding issue in your setup with
ground being completed through the wall power ground pin. Tell me exactly all
of the cables/connections going to the KPA500 (and from where). While you are
at it you might as well do the same for the KAT500. I’ll try to decipher what
is going on from this information and hopefully get a good solution for you
quickly.
73!
Jack, W6FB
Elecraft Engineering
> On Dec 30, 2018, at 1:55 PM, Ken B via Elecraft <[email protected]>
> wrote:
>
> Thanks for the suggestion
> Sorry for the delay the wife and I went out. The only way I can get it all to
> work properly is to:- Remove AC power from the AMP (simply turning it off
> dowes not work) - On the radio (icom 7600) select the band (ensure auto tuner
> on Radio is off) - On Radio select AM and depress PTT - While holding PTT,
> hit the tune button on the KAT500 - Let if get to 1.2 and stop - Let go PTT
> and select SSB on Radio- Plug in AC power to KPA and power on - On KPA select
> the proper band- On the KPA select operate from Standby
> All works until I change bands then it is start from the top Cleared all
> memory
> Wish Elecraft was open on Monday.
> ThanksKen
>
> From: Don Wilhelm <[email protected]>
> To: "[email protected]" <[email protected]>; "[email protected]"
> <[email protected]>
> Sent: Sunday, December 30, 2018 8:39 AM
> Subject: Re: [Elecraft] KAT500/KPA500 with Icom 7600 accessory cable
>
> Ken,
>
> If that Send cable is the only one you have connected between your Icom
> and the KAT500, you need to feed a bit of RF to initiate a TUNE
>
> The KAT500 will first look for a saved L/C combination for that antenna
> and frequency and will switch to that rather than doing a TUNE.
> Secondly, it will compute the SWR and if it is below 1.5, it will go
> into bypass - no tuning is necessary.
>
> Is it possible that either one of those conditions exist?
>
> 73,
> Don W3FPR
>
> On 12/30/2018 6:12 AM, Ken B wrote:
>> Yes from the 7600 accessory 1 pin 3 to the kat500
>>
>> Sent from Yahoo Mail on Android
>> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers_wl=ym_sub1=Internal_sub2=Global_YGrowth_sub3=EmailSignature>
>>
>> On Sun, Dec 30, 2018 at 4:52 AM, Don Wilhelm
>> <[email protected]> wrote:
>> Ken,
>>
>> Do you have the cable wired first to the KAT500 and then on to the
>> KPA500?
>> The KAT500 must interrupt the keying of the KPA500 when it needs
>> to tune.
>>
>> 73,
>> Don W3FPR
>>
>> On 12/29/2018 10:13 PM, Ken B wrote:
>> > Thank you Don.
>> > The pin 3 (send) did the trick perfectly. Now it works at 300 to
>> 400
>> > watts out with 20 in. The problem i have now is when i switch bands
>> > the kat will not tune unless i remove all AC power from the amp.
>> >
>> >
>> > Sent from Yahoo Mail on Android
>> >
>>
>><https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers_wl=ym_sub1=Internal_sub2=Global_YGrowth_sub3=EmailSignature
>>
>><https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers_wl=ym_sub1=Internal_sub2=Global_YGrowth_sub3=EmailSignature>>
>>
>>
>> >
>> > On Thu, Dec 27, 2018 at 11:36 PM, Don Wilhelm
>> > <[email protected] <mailto:[email protected]>> wrote:
>> > Ken,
>> >
>> > Look at your Icom 7600 documentation. I believe the
>> 'keyword' may be
>> > "Send" or Keyout or something of that nature (PTT should be an
>> > input to
>> > the transceiver, not an output, but some manufacturers mix
>> them up
>> > causing confusion - check the documentation).
>> > Connect that output from your transceiver first to the KAT500
>> AMP KEY
>> > connector and from the other KAT500 AMP KEY connector to the
>> KPA500.
>> > That allows the KAT500 to disable the amplifier keying if the
>> KAT500
>> > needs to tune.
>> >
>> > You should then be "good to go" with the basic cabling. When
>> you get
>> > the proper cable, it will integrate better with your Icom,
>> but the
>> > basic
>> > cabling will get you on the air with your new toys.
>> >
>> > 73,
>> > Don W3FPR
>> >
>> > On 12/27/2018 11:14 PM, Ken B via Elecraft wrote:
>> > > Just received my the kap500 and found out it was missing the
>> > accessory cable which goes from the icom 7600 to the kat500.
>> > Elecraft is sending one but it might take a week. In the mean
>> time
>> > does anyone have the accessory pin outs to rca plug so i can make
>> > one and use my new toy.
>> > > Thank youKenKc1icn
>> >
>>
>
>
>
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[email protected]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
