Hi Pete If you don't want to use VOX and/or QSK ............ I take both the key line and the PTT line from the WinKey to the K3. In N1MM - Config - Config Ports etc - WinKey - Set lead time to 1. Works perfectly !! 73 Roger - G4BVY
-----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of N4ZR Sent: 24 April 2019 14:15 To: Elecraft List <[email protected]> Subject: Re: [Elecraft] Clipping first element of CW - K3/KPA-1500 This appears to be, at least in part, a simple matter of RTFM. Also, my manual is 9 years old, and there's obviously been a lot of stuff added since then. Experimentally, it appears that must have *both* QSK on - whether Full or Semi - and VOX on. Once I do this, I see my first dots on the KPA-1500 bar-graph every time. I do not want to use the built-in keyer in the K3, because most of my operating is CW contesting, and I want to use the Winkeyer to send stored messages from N1MM +. The manual makes it clear (if only I'd read it) that both QSK and VOX must be enabled for CW. In PTT mode, it appears that my keyer is sending the PTT signal simultaneously with the first RF - not good. Thanks to everyone who helped put me on the right track. 73, Pete N4ZR Check out the Reverse Beacon Network at <http://reversebeacon.net>, now spotting RTTY activity worldwide. For spots, please use your favorite "retail" DX cluster. On 4/24/2019 8:49 AM, Bob McGraw K4TAX wrote: > See CW QRO and TX DELAY in the menu. Also the benefits and likely > issues are described in the manual, page 58 and 66 as MENU items. > As to using other means to key the radio and amp and send CW, those > may have their own settings as required. > > While I do not consider myself a high speed CW op, I do work QSK. I > do not find any truncation of the first CW element. I use the > internal keyer and either a Vibroplex Iambic paddle or a Vibroplex > single level paddle. I have VOX set to ON, CW QRO is OFF and TX DLY > to NOR and 008. > > Hope this helps. > > 73 > > Bob, K4TAX > > > > > On 4/24/2019 7:34 AM, Andy Durbin wrote: >> "It occurs if the rising edge of the keying waveform happens at the >> same time as the PTT line. The ONLY way around this is to delay the >> keying waveform slightly so it occurs after the PTT." >> >> That would seem to imply that you are not using CW VOX keying. If >> that is the case then wouldn't using CW VOX eliminate the issue? >> >> 73, >> Andy k3wyc >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net Please help support this >> email list: http://www.qsl.net/donate.html >> > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html --- This email has been checked for viruses by AVG. https://www.avg.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
