A friend of mine, Tim AB4B, suggested that I might need a buffer amp to keep the IF being pulled down by the sdr. DXEngineering sells the Clifton Z10000. That adds about 6db of gain, but maybe the buffering that it does has an even bigger effect.
On Fri, Oct 4, 2019 at 2:18 PM Bob McGraw K4TAX <[email protected]> wrote: > In a word, YES. I find that to be true with my K3S as well as other > brands/models of radios. Thus you'll need about 20 dB of gain in the > form of a preamp between the IF output and the QSR receiver. > > 73 > > Bob, K4TAX > > > On 10/4/2019 12:57 PM, Fred Massey wrote: > > Some. I was planning on sending an email to Elecraft support with the > s/n > > of my K3s to see if I needed the mod. The difference I’m seeing in > signal > > strength is about 20+ dB. Is it normal for the if-out to be weaker than > a > > direct connection to the antenna? > > 73, > > Fred > > AE4ED > > > > On Fri, Oct 4, 2019 at 12:44 PM Don Wilhelm <[email protected]> > wrote: > > > >> Fred, > >> > >> Have you looked the K3 IF Output mod? > >> > >> > https://ftp.elecraft.com/K3/Mod%20Notes%20Alerts/IF_Output_Buffer_Gain_Mod_Rev_A.pdf > >> > >> If you don't have the 13k SMD resistor or a 1/8 watt 13k resistor, you > >> can order the kit from Elecraft. > >> > >> 73, > >> Don W3FPR > >> > >> On 10/4/2019 1:24 PM, Fred Massey wrote: > >>> Good afternoon Wes and all, > >>> > >>> If I connect the antenna directly to the QSR-1, I get the same signal > >> level > >>> as the K3s. But, when I connect to the QSR-1 to the IF-out, the signal > >> is > >>> about 4 s-units less. > >>> > >>> Any ideas...anyone? > >>> > >>> Fred > >>> > >>> On Thu, Oct 3, 2019 at 4:14 PM Wes <[email protected]> wrote: > >>> > >>>> I use an SDR-IQ on the i-f output on my (very) early K3S. it works > >> fine. > >>>> IIRC, > >>>> always a dubious proposition, I did the mod on my original K3 and it > >>>> worked well > >>>> too without any additional amplification. I think you have another > >>>> problem. > >>>> > >>>> Wes N7WS > >>>> > >>>> On 10/3/2019 2:01 PM, Fred Massey wrote: > >>>>> Good afternoon, > >>>>> > >>>>> I have successfully connected my QSR-1 to my K3s if-out, and > >> immediately > >>>>> noticed the signal strengths showing on the QSR-1 were much weaker. > I > >>>>> probably have an early K3s, so the if-out signal strength is even > >> weaker. > >>>>> Any recommendations at a good preamp to use? It seems like 20db is > >> what > >>>> I > >>>>> need: > >>>>> > >>>>> 73, > >>>>> Fred > >>>>> AE4ED > >>>> ______________________________________________________________ > >>>> Elecraft mailing list > >>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >>>> Help: http://mailman.qth.net/mmfaq.htm > >>>> Post: mailto:[email protected] > >>>> > >>>> This list hosted by: http://www.qsl.net > >>>> Please help support this email list: http://www.qsl.net/donate.html > >>>> Message delivered to [email protected] > >>> ______________________________________________________________ > >>> Elecraft mailing list > >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >>> Help: http://mailman.qth.net/mmfaq.htm > >>> Post: mailto:[email protected] > >>> > >>> This list hosted by: http://www.qsl.net > >>> Please help support this email list: http://www.qsl.net/donate.html > >>> Message delivered to [email protected] > >>> > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to [email protected] > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
