Mike,
The red and black assembly is an Anderson Power Pole connector -
commonly called APP.
For the small receive current drawn, the voltage drop in the wire and
connectors should be close to zero, so the 0.2 volts is significant for
#12 wire unless there is something not properly tightened on the
connectors. The drop will be more substantial with the increased
current during transmit at 100 watts.
Banana plugs and jacks can be used to carry a heavy current, but some of
the ones I have seen have a poor contact method of fastening the wire to
the banana plugs - properly installed wires on banana plugs are good for
up to 30 to 50 amps. Is there any way you can connect ring terminals
onto those power supply terminals? Like removing the outer nuts from
the terminals - if so then switch to the ring terminals.
73,
Don W3FPR
On 6/30/2020 6:21 PM, Mike Kopacki wrote:
Don, don’t know what you mean by the APP assembly.
I can only see one metal part on the inside of the red and black
connectors that plug into the K2. I assume that is the “contact
blade”? I see nothing else on the inside.
But here is a possible problem, that I will throw out, knowing full
well that some will think I am not very smart…..I had to buy banana
plugs to make the power cable, which is part of the KPA-100 assembly
instructions. When I received them from MFJ, model MFJ-7713, it was a
solderless type that I had never seen before. I talked to three
people at MFJ, none could explain how the wire attached to the plug.
The third guy hung up on me.
So I connected the wire to the plug the only way I could see, but the
configuration of the plug still eludes me.
The P/S output is 13.6V. I’m seeing 13.1V at the K2. If the normal
drop is .3V, it should read 13.3V at the K2. Is the difference of .2V
“substantial”?
Mike NJ2OM
Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> for
Windows 10
*From: *Don Wilhelm <mailto:[email protected]>
*Sent: *Tuesday, June 30, 2020 6:01 PM
*To: *Mike Kopacki <mailto:[email protected]>
*Cc: *elecraft@mailman qth. net <mailto:[email protected]>
*Subject: *Re: [Elecraft] K2 K2/100 post FD review
Mike,
You should have only 0.3 volts drop IN the K2 itself, so given your
display of 13.1 volts on the K2, that says you have a substantial
voltage drop in the power cable.
Is it wired directly to the power supply? Are all the connections
tight? Is the APP assembly at the K2 correct? Look at the end of the
connector - do you see only the contact blade? or can you see the end of
the spring finger under the contact blade visible? If the spring finger
is visible, the contact blades have not been pushed in far enough -
apply pressure to the back to seat the connector.
Make the same visual check on the APP connector mounted in the KPA100.
If it needs correction, you will have to get inside the KPA100 to
correct it.
73,
Don W3FPR
On 6/30/2020 5:32 PM, Mike Kopacki wrote:
> Don...
>
> The power supply is an MFJ 13.8V/25A switching power supply. It
measures 13.63V at the terminals.
>
> The K2 shows 13.1V in receive mode.
>
> During transmit on all bands, the K2 shows 11.3-11.9V, depending on
the band.
>
> All the power connections appear to be tight.
>
> Thanks,
> Mike NJ2OM
>
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
