DW:
First of all, I note from your serial number that Elecraft sold about
22 K2's in roughly the week that separates our two purchases.
Interesting bit of data. I wish them well, and hope that they make
lots of money selling us great radio designs for years to come!
Secondly, I feel your pain, since I went through the same thing with
the diffuser last week. I have to say that it has been the most head-
scratchingly odd part of the build so far. I'm just now heading into
the PA section, with everything having gone perfectly so far, except
for the 8-volt regulator on the control board only putting out a bit
over 7.5 volts. A replacement cured that (made setting the agc
voltage high enough impossible). I got a very accurate and quick
diagnosis from Gary Surrency, and a quick offer to send a new
regulator from the parts folks. Great support!
I hope that Elecraft comes up with a better way of assembly for the
diffuser, or changes it to one that has long enough leads for the
LEDs. The use of the four little pieces of pcb material as a gauge is
also mechanically dicey compared with how they apparently used to fit
over the LED wires. Now, they are just free-stacked 2-and-2 on each
side of the diffuser as you attempt to hold it and these little pieces
in place for the soldering operation. Their suggestion to hold the
assembly with a rubber band proved mechanically impossible for me, but
YMMV.
It reminds me of trying to build a stable house of cards! Since these
little pieces no longer go in the LED holes, they are simply stacked,
cordwood style, to properly space and hold up the diffuser. I had the
assembly tumble several times before managing to get it properly
soldered down. Yes, I also found that my LED leads barely touched the
pads, but it sounds like maybe mine were just a fraction longer than
yours, as I'm reasonably happy with the slight metal-to-metal contact,
but the leads are just barely touching the pads. A little extra
solder helps.
That said, I'm very, very pleased with my K2 build so far, and can't
wait to get it up and running.
Lastly, does this count as Elecraft mojo or not? I've made CW QSO's
on 17m and 15m with VP6DX's great K3's while building my K2 about 5
feet away from my operating position! Those guys can really hear
anything! I was running 100 watts on an FT-847 into a small Pacific
Antenna PAC-12 vertical (essentially a mobile antenna) stuck into the
grass in my small back yard. I was so impressed with the very light
traffic they had on 17m Friday afternoon (about 2330Z) that I tried
them again on 15m, but this time running only 10 watts--closer to "K2
style." They came back on the second call. Outstanding! I'm
confirmed on their on-line log now for 2 bands, and all I had to do
was have a partially-built Elecraft radio nearby! I think that
qualifies as Proximity Mojo...
73,
Dave K7DAA
http://www.k7daa.com
On Feb 16, 2008, at 7:29 PM, DW Holtman wrote:
Ken,
Thank you for the suggestion, sounds like it will work great.
Best,
DW Holtman
WB7SSN
----- Original Message ----- From: "Ken, KA0W" <[EMAIL PROTECTED]>
To: "DW Holtman" <[EMAIL PROTECTED]>; <[email protected]>
Sent: Saturday, February 16, 2008 8:25 PM
Subject: Re: [Elecraft] K2 Assembly Question
I put a short lead in each of the holes for the solder to slightly
puddle around. Than centered the diffuser and heated each lead from
bottom of board while adding slightly more solder. Than checked and
it took well. Don't want too large of a puddle, but enuff so
diffuser leads get soldered. I wouldn't solder right next to
diffuser. I don't think it likes heat - "HI!"
Have fun!
Ken, KA0W
----- Original Message ----
From: DW Holtman <[EMAIL PROTECTED]>
To: [email protected]
Sent: Saturday, February 16, 2008 9:00:40 PM
Subject: [Elecraft] K2 Assembly Question
Hello,
Last Sunday (10 Feb) I ordered a K2, the great people at Elecraft
shipped it Monday. It arrived Wednesday (S/N 6412) and the assembly
is under way.
Everything went smooth with the control Board. Everything was going
great with the Front Panel Board until I got to installing the
Diffuser light for the LCD display.
I posted the Errata sheet for page 28. The instructions are to
install the Diffuser 1/8" off the circuit board using the spacers
provided.
The length of the leads from the LEDs in the Diffuser are 1/8", the
same length as the spacers. They cannot go into the hole on the
Front panel Circuit board. The new picture from the Errata sheet
looks like it is just soldered without any physical connection.
Just sort of lumping solder to attach the Leads to the pads on the
Circuit board without going into the hole and soldering from the
back side of the circuit board?
Is this right? Trying to get a soldering iron under the diffuser to
the pin on the top of the board to solder it looks tough to do with
out burning the diffuser or the LED bar graph.
Have I missed the boat on this?
Any help would be greatly appreciated.
Best,
DW Holtman
WB7SSN
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
