Lexa, I have loaded 2.02 and do not find the problems you describe ...
If CW is set to VOX with 200 msec delay (tail) and I switch to USB - even with VOX off in USB - and "Auto CW" enabled I get the proper CW operation/power output and VOX delay. They only suggestion I would make for the firmware is to force CW VOX ON while in SSB mode if "Auto CW" is enabled. I generally prefer PTT mode for both CW and SSB but it would be handy to override CW PTT if Auto CW was enabled. 73, ... Joe, W4TV > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of > Alexandr Kobranov > Sent: Sunday, June 08, 2008 4:39 PM > To: elecraft > Subject: Re: [Elecraft] K3: cw/vox/PTT ver 2.02 - bug? > > > Hello Mike, > > thanks to this "problem" I am totally confused now.... :-( > > Mentioned problem is maybe permanent in all previous versions, tried > 1.88 now and have the same results. > If SSB+CW active there is all the time RF out in SSB mode even if CW > mode is in PTT or VOX. The difference is that if CW is in > VOX/QSK then > DELAY is applied, if CW in PTT it is like FULL QSK > > But IMHO if SSB mode is set to PTT and also CW mode is set to PTT > there should be NO CW RF on output without any other > conditions except > PTT or XMIT or CW VOX/QSK active.(in SSB+CW) > Am I right? Or am I so rigid? > Aditonally to ensure application of CW VOX/QSK delay it (CW in SSB > mode) should be only when CW mode in VOX/QSK. > > How it is possible I was fixed so long with this idea that SSB+CW is > not working without CW mode in VOX/QSK? Maybe before 1.88 it was? > SSB+CW was at 1.87 release - I have not a copy of it :-( > > Sorry for used bandwidth caused by my stupidity :-) > 73! > Lexa ok1dst > > > > Alexandr Kobranov napsal(a): > > Mike, > > you are right... > > When you have SSB + CW active (menu:CW WGHT press "1") > there is now no > > conncetion between PTT/VOX mode for CW and CW sending in SSB mode. > > (as it was in previous versions as I remember) > > My previous messages concerning this was based on previous > experience > > and only very short test with 2.02. Sorry. > > > > It is surely bug in this beta version as NO CW QSK DELAY is applied, > > only RF based on Key is emitted. > > > > The correct function is to use CW VOX/QSK setting incl. VOX CW DELAY > > which is now ignored. > > > > To avoid CW RF ins SSB or (CW keying without QSK delay) set SSB-CW > > until > > influence of CW PTT/VOX/QSK setting will be back. Simply do not use > > Auto-CW in beta 2.02 or go back with F/W. > > > > 73! > > L. -dst- > > > > > > Mike Harris napsal(a): > >> Hi, > >> > >> Unless I'm misunderstanding something it works here. > >> > >> SSB - PTT mode, press paddle whilst in RX results in CW with RF > >> output. Interestingly this happens even if true CW mode is > not set to > >> VOX. > >> > >> Is this somehow broken in v2.02? I haven't bothered to load it yet > >> because it doesn't offer me anything I currently need and > I will let > >> the army of beta testers thrash it a bit. > >> > >> Regards, > >> > >> Mike VP8NO > >> ----- Original Message ----- From: "Ken Kopp" <[EMAIL PROTECTED]> > >> To: <[email protected]> > >> Sent: Saturday, June 07, 2008 10:38 PM > >> Subject: [Elecraft] cw/vox/PTT w/ ver 1.96/1.73 > >> > >> > >> | Same here ... no CW TX if in SSB / PTT mode. I use a > foot switch > >> | for PTT on SSB and VOX on CW. > >> | > >> | 73! Ken Kopp - K0PP > >> > >> _______________________________________________ > >> Elecraft mailing list > >> Post to: [email protected] > >> You must be a subscriber to post to the list. > >> Subscriber Info (Addr. Change, sub, unsub etc.): > >> http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/subscribers.htm > >> Elecraft web page: http://www.elecraft.com > >> > > _______________________________________________ > > Elecraft mailing list > > Post to: [email protected] > > You must be a subscriber to post to the list. > > Subscriber Info (Addr. Change, sub, unsub etc.): > > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > > Elecraft web page: http://www.elecraft.com > > > _______________________________________________ > Elecraft mailing list > Post to: [email protected] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [email protected] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
