Lexa,
I believe you are mis-interpreting What QSK DELAY does. It does *not*
increase the time before the onset of RF, but it does change the delay
after a keyup condition.
The purpose of QSK DELAY is to keep the amplifier relays held in between
code elements so one does not have to listen to the loud clacking of the
amplifier relays.
The delay of RF output after keydown is currently fixed in the K3, but
there is consideration being given to allow it to be user controlled in
the future. The adjustment range may be limited, so if you have
transverters and preamplifiers that must have a longer delay to the
onset of RF, the TX INH input would be required.
73,
Don W3FPR
Alexandr Kobranov wrote:
Hello Mike,
thanks to this "problem" I am totally confused now.... :-(
Mentioned problem is maybe permanent in all previous versions, tried
1.88 now and have the same results.
If SSB+CW active there is all the time RF out in SSB mode even if CW
mode is in PTT or VOX. The difference is that if CW is in VOX/QSK then
DELAY is applied, if CW in PTT it is like FULL QSK
But IMHO if SSB mode is set to PTT and also CW mode is set to PTT
there should be NO CW RF on output without any other conditions except
PTT or XMIT or CW VOX/QSK active.(in SSB+CW)
Am I right? Or am I so rigid?
Aditonally to ensure application of CW VOX/QSK delay it (CW in SSB
mode) should be only when CW mode in VOX/QSK.
How it is possible I was fixed so long with this idea that SSB+CW is
not working without CW mode in VOX/QSK? Maybe before 1.88 it was?
SSB+CW was at 1.87 release - I have not a copy of it :-(
Sorry for used bandwidth caused by my stupidity :-)
73!
Lexa ok1dst
Alexandr Kobranov napsal(a):
Mike,
you are right...
When you have SSB + CW active (menu:CW WGHT press "1") there is now
no conncetion between PTT/VOX mode for CW and CW sending in SSB mode.
(as it was in previous versions as I remember)
My previous messages concerning this was based on previous experience
and only very short test with 2.02. Sorry.
It is surely bug in this beta version as NO CW QSK DELAY is applied,
only RF based on Key is emitted.
The correct function is to use CW VOX/QSK setting incl. VOX CW DELAY
which is now ignored.
To avoid CW RF ins SSB or (CW keying without QSK delay) set SSB-CW
until influence of CW PTT/VOX/QSK setting will be back. Simply do not
use Auto-CW in beta 2.02 or go back with F/W.
73!
L. -dst-
Mike Harris napsal(a):
Hi,
Unless I'm misunderstanding something it works here.
SSB - PTT mode, press paddle whilst in RX results in CW with RF
output. Interestingly this happens even if true CW mode is not set
to VOX.
Is this somehow broken in v2.02? I haven't bothered to load it yet
because it doesn't offer me anything I currently need and I will let
the army of beta testers thrash it a bit.
Regards,
Mike VP8NO
----- Original Message ----- From: "Ken Kopp" <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Saturday, June 07, 2008 10:38 PM
Subject: [Elecraft] cw/vox/PTT w/ ver 1.96/1.73
| Same here ... no CW TX if in SSB / PTT mode. I use a foot
| switch for PTT on SSB and VOX on CW.
|
| 73! Ken Kopp - K0PP
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft Help:
http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft Help:
http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
------------------------------------------------------------------------
No virus found in this incoming message.
Checked by AVG.
Version: 8.0.100 / Virus Database: 270.0.0/1489 - Release Date: 6/7/2008 11:17 AM
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
