Mike,
Is the COM1 port properly working? I have seen COM port conflicts where two
COM1 ports appeared in the hardware manager of Windows. One of the ports
belonged to software for a network analyzer. Even if the analyzer software
was not running and the analyzer was disconnected, the COM1 was visible
twice. Programs like Microham that use virtual COM ports often conflict with
other programs that use COM ports. Logging software can also claim COM
ports, even if this software is not running.
After doing some COM port changes on the computer, do a reboot sometimes.
Today I had put the K3 Firmware Software on the laptop, and after changing
the KUSB from COM4 to COM1 a reboot was necessary because COM1 could not be
seen before the reboot.
Try another PC if available to check.
Steef PA2A
#1184
----- Original Message -----
From: "Mike N8XPQ" <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Saturday, July 05, 2008 12:55 PM
Subject: RE: [Elecraft] K3 Help
I am using COM 1 and it is the only one available in the drop down list of
the K3 utility. The streaming characters stop when I unplug the COM cable
from the rear of the rig. This tells me that the K3 is for some reason
sending a solid stream of characters that can be seen in the command
tester
page. The firmware page continues to say K3 is not responding or unable to
communicate with K3. I have no idea why the rig would be sending a stream
of
characters.
Mike
Dick Dievendorff wrote:
The K3 Utility command tester is showing you the characters it is
receiving.
Something is sending data over that COM port.
Please make sure that the COM port you have selected in the PORTS tab is
the
one connected to your K3.
Try turning your K3's power off (by removing the power connector, if
necessary) and see if the data streaming stops. If it doesn't, the data
isn't coming from your K3; maybe the COM port is connected to something
else, or perhaps there's a defective cable.
Dick, K6KR
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Mike N8XPQ
Sent: Friday, July 04, 2008 6:01 PM
To: [email protected]
Subject: Re: [Elecraft] K3 Help
I have noticed something new as well. When I click on the command tester
tab,
the window pops up and a strange "y" with 2 dots over top of it are
rapidly
scrolling across the screen and filling it up.Hmmmm very strange?????
When
I
disconnect the serial cable from the rig, it stops.
Mike
Mike N8XPQ wrote:
My K3 is stuck in MCU LD mode. I have tried everything in reference to
the
com port settings. The K3 utility continues to say K3 not communicating.
I
have the latest version of the utility and have attempted to re-load
2.10
firmware as well as 2.13 with no luck. I have also tried forcing a
firmware load per the manual and directions in the firmware help files.
Still no luck. Any ideas????? I really don't want to be with a "dead"
rig
all weekend.
Thanks,
Mike N8XPQ
-----
Mike Koetje N8XPQ
--
View this message in context:
http://www.nabble.com/K3-Help-tp18287766p18288055.html
Sent from the Elecraft mailing list archive at Nabble.com.
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
-----
Mike Koetje N8XPQ
--
View this message in context:
http://www.nabble.com/K3-Help-tp18287766p18291119.html
Sent from the Elecraft mailing list archive at Nabble.com.
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: [email protected]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
