What files are in your firmware folder that contains MCU revision 3.19? It should have hfpf0101.hex as well as hmcu0319.hex, hdsp0217.hex, haux0217.hex, dtbl0009.hex and tboot7.hex. The fact that your error message says it's trying to load hfpf0100 (.hex) suggests that you've got hmcu0319.hex and hfpf0100.hex but not hfpf0101.hex in the firmware folder you're loading from. You need the most recent hfpf0101.hex in the same firmware folder that you are loading MCU version 3.19 from.
This is what I mean by "mixing". The beta firmware zip firmware file contains a complete set of firmware files. All those files need to be in the firmware folder you're loading from. Dick, K6KR -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Paul Ferguson Sent: Thursday, June 18, 2009 7:33 PM To: [email protected] Subject: Re: [Elecraft] K3 Load fails I don't think I am mixing anything. I have a folder for 3.14 and one for the new Beta 3.19. When I get ready to do a load, I see what is now installed in my K3 before I "Send All Firmware to K3". After trying to load 3.19 it says Installed in the K3: MCU = 03.19, FPF = N/A, DSP1 = 02.16, DSP2 = 0219, DVR = 01.03. Available: MCU = 03.19, FPF = 01.01, DSP1 = 02.17, DSP2 = 02.17. This seems to be what would be expected if the load failed and my I previously had a good 3.14 firmware load. When I try to reload from my 3.14 folder, I end with MCU = 03.14 and FPF = N/A. This seems what I would expect if the MCU load works and the FPF load aborts. 73, Paul > As I recall there is a new FPF version that you may need to put into > the same firmware folder as your new MCU version. > > Dint try to mix... > > Dick, K6KR > > > > Sent from my iPhone > > On Jun 18, 2009, at 6:05 PM, "Paul Ferguson" <[email protected]> > wrote: > > > I have K3 #757. It was running fine on firmware 3.14. I tried to > > load the 3.19 > > Beta version. The MCU load completed OK. It then failed on the FPF > > load with > > the following messages: > > > > --------------- > > FPF firmware file hfpf0100.hex verified > > Erasing flash memory > > Sending firmware file hfpf0100.hex to FPF > > Send FPF firmware failed at load address x03C0 > > GetLastError returns 0xe2000012 "NACK retry limit has been > > exhausted" state 30 > > FPF firmware load failed > > --------------- > > > > I powered off and tried again with the same results. I downloaded > > 3.19 again > > and got the same results. I then tried several times to reload my > > saved version > > 3.14, but got the same error. The load address location is varies. I > > have seen > > x03C0, x0380, and x0350. > > > > I am using Elecraft Utility ver 1.2.3.18 on Windows XP with the > > Elecraft USB to > > RS232 cable. > > > > Any idea what to do next? > > > > 73, > > Paul > > K5ESW > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
