i read uart.c that is written by Andy and found some lines that maybe can
clear FIFO:

https://github.com/araisrobo/linuxcnc/blob/master/src/hal/drivers/mesa-hostmot2/uart.c#L164-L165

the data receive RX at:
https://github.com/araisrobo/linuxcnc/blob/master/src/hal/drivers/mesa-hostmot2/uart.c#L296-L332

When you said "disable RX", does that mean disable RX on 5i25 or RX on this
driver?

2018-03-22 10:18 GMT+07:00 Thắng Lê <lethang12...@gmail.com>:

> i 'm looking at* hm2_uart_setup,* the rx_mode describe:
> *       Bit 0* = FalseStart bit Status, 1 = false start bit detected
>        *Bit 1* = OverRun Status, 1 = overrun condition detected (no valid
> stop bit)
>        *Bit 2* = RXMaskEnable, 1= enable RXMask for half duplex
> operation, 0 = ingore RXMask
>        *Bit 4* = FIFOError, indicates that a host read has attemped to
> read more data than available. (mainly for driver debugging)
>        *Bit 5* = LostDataError, indicates that data was received with no
> room in FIFO,
> *       Bit 6* = RXMask, RO RXMASK status
> *       Bit 7* = FIFO Has Data
>
> I'm not very clearly understand when i read it,i dont see how to clear
> FIFO or disable RX from these 7 bits. I guess u mention pktuart, right?
>
>
>
> 2018-03-22 0:28 GMT+07:00 Peter C. Wallace <p...@mesanet.com>:
>
>> On Wed, 21 Mar 2018, Th?ng L? wrote:
>>
>> Date: Wed, 21 Mar 2018 15:20:12 +0700
>>> From: "[UTF-8] Th?ng L?" <lethang12...@gmail.com>
>>> Reply-To: EMC developers <emc-developers@lists.sourceforge.net>
>>> To: EMC developers <emc-developers@lists.sourceforge.net>
>>> Subject: Re: [Emc-developers] writing new firmware to read yaskawa
>>> absolute
>>>     encoder
>>>
>>> i'm using mesa_uart to read serial data but i have a issue. Sometimes,
>>>
>> after sending 8 bytes, the  phase A isnt come back idle state-5V state (it
>> keeps 0V state).  This mean uart is still getting data after first 8
>> bytes,then
>> the UART data shows me rx-bytes = 16, all  rx-data = 0.
>>
>>
>>
>>
>>
>> Is mesa_uart posible to limit the number bytes UART read?
>>
>>
>> No, but this is expected if the input is driven low after the data
>> you must only clear the UART/FIFO when the data line is idle
>>
>> You can disable RX if you know when the input data will become invalid
>>
>> (you would also expect to see the framing error bit set in this
>> circumstance)
>>
>>
>>
>> 2018-03-16 23:52 GMT+07:00 Peter C. Wallace <p...@mesanet.com>:
>>
>> On Fri, 16 Mar 2018, Th?ng L? wrote:
>>>
>>> Date: Fri, 16 Mar 2018 23:43:49 +0700
>>>
>>>> From: "[UTF-8] Th?ng L?" <lethang12...@gmail.com>
>>>> Reply-To: EMC developers <emc-developers@lists.sourceforge.net>
>>>> To: EMC developers <emc-developers@lists.sourceforge.net>
>>>> Subject: Re: [Emc-developers] writing new firmware to read yaskawa
>>>> absolute
>>>>     encoder
>>>>
>>>> ah, i understood what you mean. thank you very much
>>>>
>>>>
>>> 2018-03-16 23:30 GMT+07:00 andy pugh <bodge...@gmail.com>:
>>>
>>> On 16 March 2018 at 16:27, Thÿÿÿÿng Lÿÿÿÿ <lethang12...@gmail.com>
>>> wrote:
>>>
>>>> > this is a great idea but how can i right-shift the data? Both your way
>>>> and
>>>> > Peter's way seem have to touch UART  source
>>>>
>>>> No, you can shift the raw data in the HAL component that interprets the
>>>> data.
>>>>
>>>> --
>>>> atp
>>>> "A motorcycle is a bicycle with a pandemonium attachment and is
>>>> designed for the especial use of mechanical geniuses, daredevils and
>>>> lunatics."
>>>> ÿÿÿÿ George Fitch, Atlanta Constitution Newspaper, 1916
>>>>
>>>>
>>> Actually theres no shifting involved, only manipulating bit 7 of the
>>> 8 bit data
>>>
>>> Peter Wallace
>>> Mesa Electronics
>>>
>>> ------------------------------------------------------------
>>> ------------------
>>> Check out the vibrant tech community on one of the world's most
>>> engaging tech sites, Slashdot.org! http://sdm.link/slashdot
>>> _______________________________________________
>>> Emc-developers mailing list
>>> Emc-developers@lists.sourceforge.net
>>> https://lists.sourceforge.net/lists/listinfo/emc-developers
>>>
>>>
>>>
>>
>> --
>> Lÿÿ Thÿÿÿÿng
>> Phone: (+84) 1222443855
>> Email: lethang12...@gmail.com
>> ------------------------------------------------------------
>> ------------------
>> Check out the vibrant tech community on one of the world's most
>> engaging tech sites, Slashdot.org! http://sdm.link/slashdot
>> _______________________________________________
>> Emc-developers mailing list
>> Emc-developers@lists.sourceforge.net
>> https://lists.sourceforge.net/lists/listinfo/emc-developers
>>
>> Peter Wallace
>> Mesa Electronics
>>
>> (\__/)
>> (='.'=) This is Bunny. Copy and paste bunny into your
>> (")_(") signature to help him gain world domination.
>>
>> ------------------------------------------------------------
>> ------------------
>> Check out the vibrant tech community on one of the world's most
>> engaging tech sites, Slashdot.org! http://sdm.link/slashdot
>> _______________________________________________
>> Emc-developers mailing list
>> Emc-developers@lists.sourceforge.net
>> https://lists.sourceforge.net/lists/listinfo/emc-developers
>>
>>
>
>
> --
> Lê Thắng
> Phone: (+84) 1222443855
> Email: lethang12...@gmail.com
>



-- 
Lê Thắng
Phone: (+84) 1222443855
Email: lethang12...@gmail.com
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
_______________________________________________
Emc-developers mailing list
Emc-developers@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-developers

Reply via email to