"""And it totally ignores swarf or tool induced shorts when not actually doing a g38.x. """ And... When you want the probe and have the swarf short... Whaddayado then? Did you remap to add a message and a M00, or an air blast ? Tomp
On Sat, Jun 30, 2018, 22:19 Gene Heskett <ghesk...@shentel.net> wrote: > On Saturday 30 June 2018 06:23:04 Gene Heskett wrote: > > > On Friday 29 June 2018 20:06:44 andy pugh wrote: > > > On 30 June 2018 at 00:52, Gene Heskett <ghesk...@shentel.net> wrote: > > > > Looks good Andrew, thanks. But checking the man page, its under > > > > DEBUGGING and subject to going away at any time. Not good when > > > > this code might be legacy code someday. > > > > > > I don't think that one will be removed. It's too useful. Far more > > > likely to be promoted to permanent. > > > > > > > A bitslice to change that 5 into 3 setup pins for a lut5, so 2 > > > > additional modules get loaded by hal. Or is there a simpler way? > > > > > > It's awkward as it is S32. > > > > That indicates the select8 might be the correct module to detect > > motion.motion-type=5. > > > > So: > > loadrt select8 count=1 > > addf select8.0 servo-thread > > > > later in .hal file: > > net probe-ctl <= motion.motion-type => select8.0.sel # disable out5 if > > not probeing move net probe-sense <= hm2_5i25.0.gpio.003.in_not => > > select8.0.enable # edit "not" for correct action net probe-hit <= > > select8.0.out5 => motion.probe-input # signal source is p3-15, > > gpio.003 > > > > But that gets an error exit: > > twopass: Error in file ./GO704fast.hal: > > Pin 'select8.0.enable' does not exist > > > > ??? read man 9 select8, several times, can't see error. Lost mind? man > > page error??? comment that line out, its runs. halmeter says its not a > > pin, but a parameter? > > > > 'scuse me but what good is a parameter, which the manpage says it is: > > PARAMETERS > > select8.N.enable > > bit rw (default: TRUE) Set enable to FALSE to cause all > > outputs to be set FALSE Note the rw... > > > > Crazy, it was a Wurlitzer. Can it be made into a pin? Many times more > > usefull. How many previous users would that break? > > > > me goes wandering off & back to bed. > > > > I'll have to add an and2 I guess. Send select8.0.out5 >and2.N,in0, > > probe-hit to and2.N.in1, and2.N.out => motion.probe-in > > And that worked. And it totally ignores swarf or tool induced shorts > when not actually doing a g38.x. Now all I have to add is the last 2 of > the 3 operations to install the keying cap screw in the side of the > slug. The 2mm deep slot is being cut right now. > > > -- > Cheers, Gene Heskett > -- > "There are four boxes to be used in defense of liberty: > soap, ballot, jury, and ammo. Please use in that order." > -Ed Howdershelt (Author) > Genes Web page <http://geneslinuxbox.net:6309/gene> > > > ------------------------------------------------------------------------------ > Check out the vibrant tech community on one of the world's most > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-developers mailing list > Emc-developers@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-developers > ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-developers mailing list Emc-developers@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-developers
