IIRC the thing that got us was the requirement that the safety ground be bolted to the metal chassis. Again, if I recall correctly (it's been about ten years), we had to work with the filter mfr. on that one.
Cortland ====================== Original Message Follows ==================== >> Date: 04-Dec-00 20:36:15 MsgID: 1077-7377 ToID: 72146,373 From: "mike harris" >INTERNET:[email protected] Subj: Re: AC inlet Chrg: $0.00 Imp: Norm Sens: Std Receipt: No Parts: 1 From: "mike harris" <[email protected]> Subject: Re: AC inlet List-Post: [email protected] Date: Mon, 4 Dec 2000 20:22:49 -0800 Reply-To: "mike harris" <[email protected]> I have been involved with a monitor that had a PWB-mounted filter, and the ground was provided through a PWB trace. That trace was subjected to a 1000 A fault test, and passed. Mike Harris/Teccom Co. -----Original Message----- From: Cortland Richmond <[email protected]> To: Tudor, Allen <[email protected]>; ieee pstc list <[email protected]> List-Post: [email protected] Date: Friday, December 01, 2000 10:29 PM Subject: Re: AC inlet > >At a former employer, one of our power supplies used a PWB mounted, canned >filter. However, securing an adequate third-wire ground required that it be >bolted to the chassis. > >Cortland > >PS: If you're in Irvine, ONE of my former employers was right across the >street from you. > >cer > >====================== Original Message Follows ==================== > > >> Date: 01-Dec-00 12:17:18 MsgID: 1077-6566 ToID: 72146,373 >From: "Tudor, Allen" >INTERNET:[email protected] >Subj: AC inlet >Chrg: $0.00 Imp: Norm Sens: Std Receipt: No Parts: 1 > >From: "Tudor, Allen" <[email protected]> >Subject: AC inlet >Date: Fri, 1 Dec 2000 12:08:26 -0800 >Reply-To: "Tudor, Allen" <[email protected]> > > >Greetings, > >Is anyone aware of an ac inlet with line filter that mounts on a printed >wiring board? What I'm thinking of is something like the chassis mount >versions made by Schruter, Corcom, & Delta. Any leads would be >appreciated. > >Thanks in advance. > >------------------------------------------- >This message is from the IEEE EMC Society Product Safety >Technical Committee emc-pstc discussion list. > >To cancel your subscription, send mail to: > [email protected] >with the single line: > unsubscribe emc-pstc > >For help, send mail to the list administrators: > Jim Bacher: [email protected] > Michael Garretson: [email protected] > >For policy questions, send mail to: > Richard Nute: [email protected] > >====================== End of Original Message ===================== > >------------------------------------------- >This message is from the IEEE EMC Society Product Safety >Technical Committee emc-pstc discussion list. > >To cancel your subscription, send mail to: > [email protected] >with the single line: > unsubscribe emc-pstc > >For help, send mail to the list administrators: > Jim Bacher: [email protected] > Michael Garretson: [email protected] > >For policy questions, send mail to: > Richard Nute: [email protected] > > ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: [email protected] Michael Garretson: [email protected] For policy questions, send mail to: Richard Nute: [email protected] ====================== End of Original Message ===================== ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: [email protected] Michael Garretson: [email protected] For policy questions, send mail to: Richard Nute: [email protected]
