Dan, Without knowing any detail on your product, my vote is to say that all of the requirements of 60950 that apply to any other power supply would apply in full to a hot swappable supply. Assuming the supply you're handling is akin to a bank of rectifiers in a shelf, the shelf would also need space fillers to close off access to hazardous parts in the event that a full complement of supplies is not used. I assume the over-all design addresses in-rush currents at both the supply and shelf ends, labels, warnings, instructions, etc....the full monty.
My opinion and not that of my employer. Regards, Kaz Gawrzyjal [email protected] -----Original Message----- From: Richardson, William G [mailto:[email protected]] Sent: Wednesday, June 20, 2001 4:50 PM To: 'Dan Teninty' Cc: '[email protected]' Subject: RE: Hot Swappable Power Supplies ? There must be a bleeder resistor (across the X caps) to make the AC input pins safe to touch once the supply is removed from the cabinet. If there are exposed voltage or energy hazards with the supply removed, there must be a restriction such that only trained personnel are instructed to do this OR a tool must be used to remove the supply. -----Original Message----- From: Dan Teninty [mailto:[email protected]] Sent: Wednesday, June 20, 2001 4:16 PM To: Emc-Pstc@Majordomo. Ieee. Org Subject: Hot Swappable Power Supplies ? Do any of my esteemed colleagues know of any specific requirements in 60950 (UL/CSA or EN) relating specifically to hot swappable power supplies? A search in the PDF version of UL/CSA 60950 reveals nothing specific when searching for "hot", "swap", or "power supply". A visual search of the TOC also reveals nothing specific. 2.6.5.4 deals with : Parts that can be removed by an operator Protective earthing connections shall make earlier and break later than the supply connections in each of the following: - the connector of a part that can be removed by an OPERATOR; - a plug on a power supply cord; - an appliance coupler. Compliance is checked by inspection. This is the most I could find that was related, and then it is referring to the AC side. Thought I would triple check with the collective brain trust to be sure. Appreciate any pointers to passages that I missed. Thanks, Daniel E. Teninty, P.E. Managing Partner DTEC Associates LLC Streamlining the Compliance Process 5406 S. Glendora Drive Spokane, WA 99223 (509) 443-0215 (509) 443-0181 fax ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Michael Garretson: [email protected] Dave Heald [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.rcic.com/ click on "Virtual Conference Hall," ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Michael Garretson: [email protected] Dave Heald [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.rcic.com/ click on "Virtual Conference Hall," ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Michael Garretson: [email protected] Dave Heald [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.rcic.com/ click on "Virtual Conference Hall,"
