Michael, I installed a medium size GTEM and I purchased the table from EMCO at that time now its ETS. The table itself is quite complicated with motors and two dimensional rotations. When its all said and done it would be money well spent on buying it from the manufacturer and having them install it. With all the down sizing you might come across a used table out there but I would still recommend that you have ETS install it. The external motors are quite large and heavy its a multi person task and quite dangerous. Your locate ETS rep could help you locate a used GTEM or at least the table (manipulator). Good Luck, Mark J. Kirincic [email protected]
----- Original Message ----- From: Dan <mailto:[email protected]> Anchondo To: [email protected] ; [email protected] ; [email protected] Sent: Friday, October 08, 2004 12:20 PM Subject: RE: GTEM Test Table Michael Derek's right and I had forgotten about the messing. If there is a recommended table you can buy get that one. I have installed equipment (controllers,video,masts) that was bought after the fact and you will have messing time. Messing means you find it,whom to pay for it,buy it,deliver it,build it,install it and hopefully it works. Regards Dan Anchondo From: [email protected] mailto:[email protected]]On Behalf Of [email protected] Sent: Friday, October 08, 2004 9:32 AM To: [email protected]; [email protected]; [email protected] Subject: Re: GTEM Test Table In a message dated 10/8/2004 11:22:44 AM Central Daylight Time, [email protected] writes: All If you know a cabinet-maker or a good carpenter they should know how to construct a non-metallic table for you. Be very clear about the non-metallic part (no nails no screws )and the weight load,and indoor or outdoor usage. They can usually buid it on site. I had a friend build one and I had to explain the non-metallic part a couple of times. I think its not a natural thing to make a non-metallic table. Regards IMHO Dan Anchondo Vivotech,Inc Just as an asside, you may still want to think about buying one. It should be made of plastic parts, not wood. After all the messing is over.... Of course, I'd like to throw Schaffners positioner into the list of options. Derek N. Walton Owner, L F Research EMI Design and Test Facility Poplar Grove, IL 61065 ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. Website: http://www.ieee-pses.org/ To post a message to the list, send your e-mail to [email protected] Instructions: http://listserv.ieee.org/listserv/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Ron Pickard: [email protected] Dave Heald: [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. Website: http://www.ieee-pses.org/ To post a message to the list, send your e-mail to [email protected] Instructions: http://listserv.ieee.org/listserv/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Ron Pickard: [email protected] Dave Heald: [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. Website: http://www.ieee-pses.org/ To post a message to the list, send your e-mail to [email protected] Instructions: http://listserv.ieee.org/listserv/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Ron Pickard: [email protected] Dave Heald: [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc
