Hello, Gert. I agree; it's all too easy for issues that have in fact
been settled to grow into myths.
Best wishes
John Woodgate OOO-Own Opinions Only
J M Woodgate and Associates www.woodjohn.uk
Rayleigh, Essex UK
On 2019-08-24 12:32, Gert Gremmen wrote:
John
Nice to agree then. :-)
The new assessment system has needed fine tuning during quite a
period, and some misunderstandings might have grown to the size of hoaxes.
Gert
On 24-8-2019 13:06, John Woodgate wrote:
We disagree much less that you might think. I'll just pick up two points:
/here are even hints that some legal people believe that every
product of a given type, e.g electric fan, should have the same
performance!
/
The hints aren't restricted to things that indeed are common, like
safety provisions, but extend to the whole product
specification.//That may be a misinterpretation, but it's how it's
seen by people who don't have your insight./
/
"I can assure you that manufacturers will be able to define the
properties of their equipment."
That is not how the rewrite of the EMC immunity criteria is being
constrained. It seems to have been ruled that 'manufacturer' cannot
be mentioned at all.
Best wishes
John Woodgate OOO-Own Opinions Only
J M Woodgate and Associateswww.woodjohn.uk
Rayleigh, Essex UK
On 2019-08-24 11:51, Gert Gremmen wrote:
These very high standards (as you call it) are just part of the
requirements as given in ER3, for example, and are being part of the
current way the EU assesses standards in the current situation,
where standards text have become part of law -so-to-say- .
> /I can't understand why the court ruling about ENs being 'sort-of'
laws hasn't been challenged./
This decision cannot be challenged anymore as it is confirmed by the
highest EU legal authorities. It makes no sense to complain about a
status quo.
>/Because the committee decided it was necessary./
I won't challenge the committee technical expertise, but it makes no
sense writing about things that are not covered by title, scope and
foreword of the standard. The standard is to describe the (minimum)
technical requirements of the equipment in the field of EMC. The TC
should stay on their chair, defining requirements, and not mix the
interests of the standard with those of the manufacturer.
>/I can't understand why the court ruling about ENs being 'sort-of'
laws hasn't been challenged. As a result of it, the correct
decision that some ETSI standards that left crucial provisions to be
agreed between the manufacturer and the test house cannot be
permitted has been vastly over-interpreted to mean effectively that
even the word 'manufacturer' cannot be mentioned. For example, it is
not being allowed to say that the manufacturer provides the
performance specification of the product. There are even hints that
some legal people believe that every product of a given type, e.g
electric fan, should have the same performance! Do we expect all
cars to have the same performance as a Bugatti supercar?/
This is an oversimplification of what happens in reality/. /I am one
of the three assessors for ETSI standards and i can assure you that
this does not happen. As it comes to performance/, /only aspects
that _are common to all cars _(to keep your analogy) need to comply
with a kind of common property. A analogy could be the performance
of tyres or brakes, that need to be suitable for the car under test.
So if you say the same "relative performance" your analogy makes
sense and, indeed, that is what happens. All radio devices use a
common medium (ether) and the standards have to make sure every
apparatus uses not more spectrum space and power than required for
its defined purpose.
>/left crucial provisions to be agreed between the manufacturer and
the test house cannot be permitted/
Of course the manufacturer should not be able to negotiate crucial
(test) aspects with a test-house. The interest of the manufacturer,
is a completely different one that that of the EU maintaining
standards and the test house, where accredited, needs to remain
independent. Negotiation with its client would jeopardize its
accreditation anyway. I can assure you that manufacturers will be
able to define the properties of their equipment. Its true that the
word "manufacturer" has been subject of challenges in many cases
where there could be some misuse by (Euro-English) statements that
allowed impacting the effectiveness of the standards tests.
An example i found is where the standard defines the requirements
for mobile (automotive) radio and there was no minimum requirement
for the temperature range in which the frequency stability was to be
maintained. (environmental profile to be negotiated between
manufacturer and test agency). The standard thus allowed the test to
be carried out from 30-35 oC (as example). Within the EU market that
is not a realistic minimum requirement as the equipment was for
outdoor use, so it was suggested to add a minimum range more
representative to EU climates.
John, thanks for your opinion anyway (but feel free to continue the
discussions)
Gert Gremmen
On 24-8-2019 10:53, John Woodgate wrote:
I think this is another example of the high standard you set.
Please see my responses below.
Best wishes
John Woodgate OOO-Own Opinions Only
J M Woodgate and Associateswww.woodjohn.uk
Rayleigh, Essex UK
On 2019-08-24 09:29, Gert Gremmen wrote:
The discussion on languages and grammar has been very useful.
I would like your opinion and answers on the following standards
clause, as found in a concept cited harmonised EMC product family
standard:
/If hardware or software are modified subsequent to the completion
of the tests described in this standard//
//an impact analysis shall be carried out and it shall be decided
whether the EMC test shall be repeated as //
//a whole, in parts or not at all. Impact analysis and decision
shall be added to the EMC test plan for the////apparatus./
I have some questions on this clause:
1. What is this clause doing in a standard describing technical
requirements for an apparatus?
/JMW: Because the committee decided it was necessary. /
1. Shouldn't this be part of a basic standard describing the test
method?
/JMW: Very possibly, but it can be difficult and cause a long delay
for one committee, that decides that hardware and software changes
should be addressed, to refer that to the a Basic standard
committee and wait some years for that committee to agree to amend
its Basic standard and publish it./
1. Who should carry out the impact analysis (not the manufacturer
of course) and decide on what retesting to do?
/JMW: Only the manufacturer knows enough about the hardware and
software to do the assessment. Besides, no-one can take away the
manufacturer's responsibility for compliance./
1. Why this should be made part of the test plan and not in the
test report?
/JMW: It's probably a mis-wording that no-one noticed. But the test
plan should certainly document what to do about hardware and
software changes after testing./
The principle of EMC- testing equipment, is that a full test is
required upon any modification, as a modification makes it a a
different equipment, but i also understand that a strict
interpretation of this might lead to excessive test costs, and
some test reductions are possible based on EMC expertise ,
experience in testing and knowledge of the equipment. I also
consider that the EMC-directive is requiring as assessment and not
testing (though testing seems an essential part of assessing and
test reports are mentioned explicitly in the EMCD annexes.
But there is much more to say about an impact analysis than a
simple clause .....
How would you treat the problem of infinite testing, -to-be-sure-,
versus realistic testing, and how would you implement such a
"impact analysis" in the different standards, in the light of
creating HS with legal effects.
/JMW: I can't understand why the court ruling about ENs being
'sort-of' laws hasn't been challenged. As a result of it, the
correct decision that some ETSI standards that left crucial
provisions to be agreed between the manufacturer and the test house
cannot be permitted has been vastly over-interpreted to mean
effectively that even the word 'manufacturer' cannot be mentioned.
For example, it is not being allowed to say that the manufacturer
provides the performance specification of the product. There are
even hints that some legal people believe that every product of a
given type, e.g electric fan, should have the same performance! Do
we expect all cars to have the same performance as a Bugatti
supercar?//
/
//
Gert Gremmen
--
Independent Expert on CE marking
Harmonised Standards (HAS-) Consultant @ European Commission for RED and EMC
EMC Consultant
Electrical Safety Consultant
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society
emc-pstc discussion list. To post a message to the list, send your
e-mail to <emc-p...@ieee.org <mailto:emc-p...@ieee.org>>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Attachments are not permitted but the IEEE PSES Online Communities
site at http://product-compliance.oc.ieee.org/ can be used for
graphics (in well-used formats), large files, etc.
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to
unsubscribe)
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Scott Douglas <sdoug...@ieee.org <mailto:sdoug...@ieee.org>>
Mike Cantwell <mcantw...@ieee.org <mailto:mcantw...@ieee.org>>
For policy questions, send mail to:
Jim Bacher <j.bac...@ieee.org <mailto:j.bac...@ieee.org>>
David Heald <dhe...@gmail.com <mailto:dhe...@gmail.com>>
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society
emc-pstc discussion list. To post a message to the list, send your
e-mail to <emc-p...@ieee.org <mailto:emc-p...@ieee.org>>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Attachments are not permitted but the IEEE PSES Online Communities
site at http://product-compliance.oc.ieee.org/ can be used for
graphics (in well-used formats), large files, etc.
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to
unsubscribe)
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Scott Douglas <sdoug...@ieee.org <mailto:sdoug...@ieee.org>>
Mike Cantwell <mcantw...@ieee.org <mailto:mcantw...@ieee.org>>
For policy questions, send mail to:
Jim Bacher <j.bac...@ieee.org <mailto:j.bac...@ieee.org>>
David Heald <dhe...@gmail.com <mailto:dhe...@gmail.com>>
--
Independent Expert on CE marking
Harmonised Standards (HAS-) Consultant @ European Commission for RED and EMC
EMC Consultant
Electrical Safety Consultant
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society
emc-pstc discussion list. To post a message to the list, send your
e-mail to <emc-p...@ieee.org <mailto:emc-p...@ieee.org>>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Attachments are not permitted but the IEEE PSES Online Communities
site at http://product-compliance.oc.ieee.org/ can be used for
graphics (in well-used formats), large files, etc.
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to
unsubscribe)
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Scott Douglas <sdoug...@ieee.org <mailto:sdoug...@ieee.org>>
Mike Cantwell <mcantw...@ieee.org <mailto:mcantw...@ieee.org>>
For policy questions, send mail to:
Jim Bacher <j.bac...@ieee.org <mailto:j.bac...@ieee.org>>
David Heald <dhe...@gmail.com <mailto:dhe...@gmail.com>>
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society
emc-pstc discussion list. To post a message to the list, send your
e-mail to <emc-p...@ieee.org <mailto:emc-p...@ieee.org>>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Attachments are not permitted but the IEEE PSES Online Communities
site at http://product-compliance.oc.ieee.org/ can be used for
graphics (in well-used formats), large files, etc.
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to
unsubscribe)
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Scott Douglas <sdoug...@ieee.org <mailto:sdoug...@ieee.org>>
Mike Cantwell <mcantw...@ieee.org <mailto:mcantw...@ieee.org>>
For policy questions, send mail to:
Jim Bacher <j.bac...@ieee.org <mailto:j.bac...@ieee.org>>
David Heald <dhe...@gmail.com <mailto:dhe...@gmail.com>>
--
Independent Expert on CE marking
Harmonised Standards (HAS-) Consultant @ European Commission for RED and EMC
EMC Consultant
Electrical Safety Consultant
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society
emc-pstc discussion list. To post a message to the list, send your
e-mail to <emc-p...@ieee.org <mailto:emc-p...@ieee.org>>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Attachments are not permitted but the IEEE PSES Online Communities
site at http://product-compliance.oc.ieee.org/ can be used for
graphics (in well-used formats), large files, etc.
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to
unsubscribe)
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Scott Douglas <sdoug...@ieee.org <mailto:sdoug...@ieee.org>>
Mike Cantwell <mcantw...@ieee.org <mailto:mcantw...@ieee.org>>
For policy questions, send mail to:
Jim Bacher <j.bac...@ieee.org <mailto:j.bac...@ieee.org>>
David Heald <dhe...@gmail.com <mailto:dhe...@gmail.com>>
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society emc-pstc discussion
list. To post a message to the list, send your e-mail to <emc-p...@ieee.org>
All emc-pstc postings are archived and searchable on the web at:
http://www.ieee-pses.org/emc-pstc.html
Attachments are not permitted but the IEEE PSES Online Communities site at
http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used
formats), large files, etc.
Website: http://www.ieee-pses.org/
Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe)
List rules: http://www.ieee-pses.org/listrules.html
For help, send mail to the list administrators:
Scott Douglas <sdoug...@ieee.org>
Mike Cantwell <mcantw...@ieee.org>
For policy questions, send mail to:
Jim Bacher: <j.bac...@ieee.org>
David Heald: <dhe...@gmail.com>