Try to remove what can be removed mechanically with a scraper etc. Then I use strong anionic detergents like in household baking oven cleaner or motorcycle spray, letting them soak in for an hour or so, reapplying wehre drops have run down or drying shows. Only the very last traces are left for organic solvents. I used to know a shop where used machinery was cleaned up and made ready for re-selling. They had an ordinary hand held high pressure gun, but instead of hot water supplied with hot heating oil (or kerosene, if you like), the machines being supported on gratings above a car washing pit. There is no dirt that can withstand that. Afterwards, to remove the oil, washing with detergents and hot air drying followed. After all this the machines were ready to be sprayed with new paint.
Peter Am 29.03.2015 01:42, schrieb richsh...@comcast.net: > I just bought a 1975 vintage Anayak FV2 mill, imported to the US by DoAll. It > has so much grease, muck, and yuck on it, I need to clean it. So far I've > tried citrus based solvent, paint thinner, automotive, parts cleaner...... > Applying it via green and brown scotch brite pads. Any suggestions on a > degrease process? > > ----- Original Message ----- > > From: emc-users-requ...@lists.sourceforge.net > To: emc-users@lists.sourceforge.net > Sent: Saturday, March 28, 2015 2:44:22 PM > Subject: Emc-users Digest, Vol 107, Issue 78 > > Send Emc-users mailing list submissions to > emc-users@lists.sourceforge.net > > To subscribe or unsubscribe via the World Wide Web, visit > https://lists.sourceforge.net/lists/listinfo/emc-users > or, via email, send a message with subject or body 'help' to > emc-users-requ...@lists.sourceforge.net > > You can reach the person managing the list at > emc-users-ow...@lists.sourceforge.net > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of Emc-users digest..." > > > Today's Topics: > > 1. Re: Possible New Lathe (richsh...@comcast.net) > 2. ot: voltage and steppers (kqt4a...@gmail.com) > 3. Re: ot: voltage and steppers (Dave Cole) > 4. Re: ot: voltage and steppers (kqt4a...@gmail.com) > 5. 2.6.4 to 2.6.7 update without a network connection? > (Gregg Eshelman) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Sat, 28 Mar 2015 15:24:42 +0000 (UTC) > From: richsh...@comcast.net > Subject: Re: [Emc-users] Possible New Lathe > To: emc-users@lists.sourceforge.net > Message-ID: > <1991675046.16595850.1427556282912.javamail.zim...@comcast.net> > Content-Type: text/plain; charset=utf-8 > > Boris? Obviously, an oversize Van Norman vertical mill, I'd say 7,000 lbs or > so. > > ----- Original Message ----- > > From: emc-users-requ...@lists.sourceforge.net > To: emc-users@lists.sourceforge.net > Sent: Friday, March 27, 2015 11:45:16 PM > Subject: Emc-users Digest, Vol 107, Issue 76 > > Send Emc-users mailing list submissions to > emc-users@lists.sourceforge.net > > To subscribe or unsubscribe via the World Wide Web, visit > https://lists.sourceforge.net/lists/listinfo/emc-users > or, via email, send a message with subject or body 'help' to > emc-users-requ...@lists.sourceforge.net > > You can reach the person managing the list at > emc-users-ow...@lists.sourceforge.net > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of Emc-users digest..." > > > Today's Topics: > > 1. Re: Converting straight lines to arcs? (andy pugh) > 2. Re: Tsudakoma TRNC-201S on a bridgeport Interact Series II? > Crazy? (Gregg Eshelman) > 3. Re: Possible New Lathe (Gregg Eshelman) > 4. Anyone have leftovers from a 9x20 CNC conversion? (Gregg Eshelman) > 5. Re: Possible New Lathe (Gregg Eshelman) > 6. Re: Velocity closed loop + Position losed loop on an axis > (Jon Elson) > 7. Re: Velocity closed loop + Position losed loop on an axis > (Karlsson & Wang) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Sat, 28 Mar 2015 00:36:39 +0000 > From: andy pugh <bodge...@gmail.com> > Subject: Re: [Emc-users] Converting straight lines to arcs? > To: "Enhanced Machine Controller (EMC)" > <emc-users@lists.sourceforge.net> > Message-ID: > <CAN1+YZVdhS=mnazvq02zh_qyjpfjslncriremqhknmhhrdx...@mail.gmail.com> > Content-Type: text/plain; charset=UTF-8 > > On 28 March 2015 at 00:13, Gregg Eshelman <g_ala...@yahoo.com> wrote: >> Will it allow saving/exporting the modified G-code file? > It looks like that is _all_ it allows. > --- Diese E-Mail wurde von Avast Antivirus-Software auf Viren geprüft. http://www.avast.com ------------------------------------------------------------------------------ Dive into the World of Parallel Programming The Go Parallel Website, sponsored by Intel and developed in partnership with Slashdot Media, is your hub for all things parallel software development, from weekly thought leadership blogs to news, videos, case studies, tutorials and more. Take a look and join the conversation now. http://goparallel.sourceforge.net/ _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
