We don't have any M30's in the program.

Rick


On 7/15/2015 11:12 AM, Ken Strauss wrote:
> On the Tormach mailing list there was a report of the same error caused by
> having a M09 and M30 on the same line. Is it possible that this is a related
> problem?
>
>> -----Original Message-----
>> From: Rick Lair [mailto:r...@superiorroll.com]
>> Sent: Wednesday, July 15, 2015 10:54 AM
>> To: Enhanced Machine Controller (EMC)
>> Subject: Re: [Emc-users] Bug:Call Stack Under run
>>
>> Hello Seb,
>>
>> I have been working on this all week,  I have run this program numerous
> times
>> on my simulator test PC in my office without any issue, as soon as I try
> to run it
>> on the machine, it gives us this fault. This morning I made a new config
> using
>> the Axis GUI, and it gives us the same fault, (we are running Gmoccapy on
> our
>> turning centers, and wanted to make sure it wasn't a GUI issue).
>>
>> The only thing different between my test PC, and the machines are the
> added
>> m-codes for the gear change, and for the tail stock commands, and we use
> the
>> TXXYY tool change format on the lathes, so I modified the g-code program
> to
>> eliminate the m-codes for the gear change, and tailstock, and change the
> tool
>> changes to the MxTy format.
>>
>> The M-codes, and tool change work fine through MDI, and with other
>> programs, so I don't think that is the issue. The supervisor has removed
>> different sections of the program, and it will run, he puts them back in,
> and it
>> won't run,
>>
>> It doesn't matter which section he removes though ( no one section would
>> specifically give or not give the fault ), the only thing we have found
> was
>> program size made a difference, The main program is 367 lines long
>> 6736 KB's, if it was kept under about 260 lines, or 5KB's
>>
>> Attached is the program we are dealing with, the file ending in rev2 is
> what I
>> am using on my test PC.
>>
>>
>> Thanks
>>
>> Rick
>>
>> On 7/10/2015 6:04 PM, Sebastian Kuzminsky wrote:
>>> On 7/10/15 3:43 PM, Jeff Johnson wrote:
>>>> I have a program with threading G33 that will run if I take the
> threading
>>>> out of it but throw an error of "Bug: Call Stack Under Run" if I leave
> the
>>>> threading in the program. We use a post processor for our programs and
>> have
>>>> done threading in the past but this one is persistent. Any Ideas?
>>> Can you reproduce the problem by running the problematic gcode in a
>>> standard sim config?
>>>
>>>
>> --
>>
>> Thanks
>>
>>
>> Rick Lair
>> Superior Roll & Turning LLC
>> 399 East Center Street
>> Petersburg MI, 49270
>> PH: 734-279-1831
>> FAX: 734-279-1166
>> www.superiorroll.com
>
>
>
> ------------------------------------------------------------------------------
> Don't Limit Your Business. Reach for the Cloud.
> GigeNET's Cloud Solutions provide you with the tools and support that
> you need to offload your IT needs and focus on growing your business.
> Configured For All Businesses. Start Your Cloud Today.
> https://www.gigenetcloud.com/
> _______________________________________________
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users

-- 

Thanks


Rick Lair
Superior Roll & Turning LLC
399 East Center Street
Petersburg MI, 49270
PH: 734-279-1831
FAX: 734-279-1166
www.superiorroll.com


------------------------------------------------------------------------------
Don't Limit Your Business. Reach for the Cloud.
GigeNET's Cloud Solutions provide you with the tools and support that
you need to offload your IT needs and focus on growing your business.
Configured For All Businesses. Start Your Cloud Today.
https://www.gigenetcloud.com/
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Reply via email to