Although I have a tiny 4" table with a stepper, I'm also fortunate enough to have a Harmonic Drive like the one Andy has along with the STMBL drive.. When I finally get around to casting the holder it will be tall enough to hold a 10" face plate but no wider than the mill table.
I am eventually planning on a tool changer since I have a number of TT holders but I don't expect it to be in the way for homing. John > -----Original Message----- > From: Gene Heskett [mailto:ghesk...@shentel.net] > Sent: May-25-18 9:48 AM > To: emc-users@lists.sourceforge.net > Subject: Re: [Emc-users] rotary tables, was Home switches. > > On Friday 25 May 2018 08:41:42 TERRY Christophersen wrote: > > > Table toward you and to the left is machine home. > > 4th axis on the right hand side of the table. > > This is how most machines are. > > > Which direction/angle is the motor sticking out? Any direct drive to the > drive worm is an un-handy direction, so in order to clear stuff, my > little table has to be on the left, so the drive motor projects at a 45 > degree angle up and to the front. Its a piece of India made 4" junk. > Handy for facing bolt head flats, or for drilling and tapping for the > grub screws for these tap hats I am making 2 or 3 a day, but useless for > cutting sprockets or gears. Backlash is measured in degrees, and varies > because the bull gear is off center. > > I needed a special drill while installing the safety railing for the > wheelchair ramp, so I made a 3 fluter I had to re-sharpen several times > with it, but since the cutting forces were into it axially, I had to put > the air hose rigged to pressurize the internals, exerting a lifting > force to the table so a 270 oz/in nema 23 could turn it to do the > spiral. > > If I could find a 5" that was really precise, and whose worm shaft was > horizontal and high enough to leave room for the motor to clear the > table, I likely would have laid the card on the counter years ago. Those > 5" all angle tilting head things look good, until I ask myself can the > motor turn it under cutting loads, You can using the indexing plates, > lock it in any position, but can they move while a 1/4" round nose is > carving the workpiece? > > My mental SWAG says no. > > So an almost too big for a G0704 6" table, with the motor on a swing > mount so it can belt drive the worm with a 3/1 multiplier, while the > motor mount can be turned to place a nema 34 to its left, bottom side > when mounted vertical, or rotated so its beside the table when mounted > face up. But thats going to be 40+ lbs for this old fart to handle, I've > not ever seen one so rigged, but I can sure "make it so." That is what > we do here I think. > > I've got to, this one is an excedrin headache, and a fairly low numbered > one at that. So who makes the best 6" for raw material? Preferably NOT > made in India. > > [...] > > -- > Cheers, Gene Heskett > -- > "There are four boxes to be used in defense of liberty: > soap, ballot, jury, and ammo. Please use in that order." > -Ed Howdershelt (Author) > Genes Web page <http://geneslinuxbox.net:6309/gene> > > ---------------------------------------------------------------------------- -- > Check out the vibrant tech community on one of the world's most > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users