remember to read the spec sheet for the accuracy of the encoder - I was looking at some 15 bit encoders or some such and they didn't seem that great...
On Wed, Jun 9, 2021 at 3:14 PM John Dammeyer <[email protected]> wrote: > I've used the AMT112Q-V without any issues compared to the problems with > the US Digital ones. And they fit better. > > > > > -----Original Message----- > > From: andrew beck [mailto:[email protected]] > > Sent: June-09-21 12:36 PM > > To: Enhanced Machine Controller (EMC) > > Subject: Re: [Emc-users] CUI devices > > > > For what is lts worth you can get a 2500ppr encoder for 30usd from my > servo > > supplier. > > > > Or a a 5000ppr. > > > > Or you can go absolute. And get a 130000 something ppr encoder. They > are > > about 70usd I think > > > > I think it's 17bit. But would have to check > > > > On Thu, Jun 10, 2021, 7:31 AM Sam Sokolik < <mailto:[email protected]> > [email protected]> wrote: > > > > > in the datasheet the > > > accuracy 0.2 degrees > > > > > > so, in my mind, it is no better than a 1800 count encoder if that.. I > > > have used them in the past - they work ok for things like spindle > > > feedback. In my experience - for servo positioning feedback - it is > too > > > noisy.. > > > > > > <https://www.youtube.com/watch?v=8RWqHW2AtrA> > https://www.youtube.com/watch?v=8RWqHW2AtrA > > > > > > > > > > > > On Wed, Jun 9, 2021 at 11:50 AM Roland Jollivet < > [email protected] > > > > > > > wrote: > > > > > > > Hi > > > > > > > > I was wondering what experience people have had with the CUI > encoders. > > > > > > > > Mostly looking at the costs. The AMT13 series comes as a kit with > all the > > > > adapters, at $33 > > > > But it's supplied with no female connector. You might only realise > this > > > > when you open the box, after paying for shipping, duties and > customs..... > > > > > > > > So you try finding a mating connector, and they're fairly obscure, > but be > > > > sure to order some pins too, otherwise you just get the plastic > shell ! > > > > > > > > Alternatively buy a ready cable from CUI (Digikey) for your encoder > at > > > $25 > > > > !!!!! > > > > > > > > It all sounds like a really shitty deal to me. > > > > (a friends experience..) > > > > > > > > Roland > > > > > > > > > > > > > > > > > > > > > > > < > https://www.digikey.com/en/products/detail/cui-devices/AMT132S-V/10269185?WT.z_cid=ref_neda_dkc_buynow_cuidevices&utm_source=ecia&utm_medium=aggregator&utm_campaign=cuidevices> > https://www.digikey.com/en/products/detail/cui-devices/AMT132S- > < > https://www.digikey.com/en/products/detail/cui-devices/AMT132S-V/10269185?WT.z_cid=ref_neda_dkc_buynow_cuidevices&utm_source=ecia&utm_medium=aggregator&utm_campaign=cuidevices> > > > V/10269185?WT.z_cid=ref_neda_dkc_buynow_cuidevices&utm_source=ecia&utm_medium=aggregator&utm_campaign=cuidevice > < > https://www.digikey.com/en/products/detail/cui-devices/AMT132S-V/10269185?WT.z_cid=ref_neda_dkc_buynow_cuidevices&utm_source=ecia&utm_medium=aggregator&utm_campaign=cuidevices> > > s > > > > > > > > _______________________________________________ > > > > Emc-users mailing list > > > > <mailto:[email protected]> > [email protected] > > > > <https://lists.sourceforge.net/lists/listinfo/emc-users> > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > > > _______________________________________________ > > > Emc-users mailing list > > > <mailto:[email protected]> > [email protected] > > > <https://lists.sourceforge.net/lists/listinfo/emc-users> > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > _______________________________________________ > > Emc-users mailing list > > <mailto:[email protected]> > [email protected] > > <https://lists.sourceforge.net/lists/listinfo/emc-users> > https://lists.sourceforge.net/lists/listinfo/emc-users > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
