On 2022/04/13 16:44, Peter C. Wallace wrote:
On Wed, 13 Apr 2022, Marius wrote:
Date: Wed, 13 Apr 2022 13:16:06 +0200
From: Marius <mar...@mastercut.co.za>
Reply-To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
Subject: Re: [Emc-users] Looking for 7i92 bit file
Peter
I changed to the firmware that you recommended and I found that the
stepgen allocations are not as reported. The reported allocations is
as it is requested in PnCConf but the actual allocations are not
correct and seems to be random. I reported in the forum.
The stepgen allocations in the 7i92_5ABOBx2D.bit file match the common
"5 Axis Mach BOB" are are exactly as shown in the 7i92_5ABOBx2D.pin
pinout file,
I suspect you will have to use pncconf to setup a standard XYZA
configuration
and modify the hal/ini files for your somewhat odd (XYAB) kinematics
The B axis is actually just a slave axis to the X axis. I get all the
axis that I need but the pin allocations are not what I need. I have to
do a drop in conversion so the pinouts much match. The stepgen and
kinematics are all correct it's just the pin allocations that I cannot
change.
On 2022/04/12 16:35, Peter C. Wallace wrote:
On Tue, 12 Apr 2022, Marius wrote:
Date: Tue, 12 Apr 2022 16:22:37 +0200
From: Marius <mar...@mastercut.co.za>
Reply-To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
Subject: Re: [Emc-users] Looking for 7i92 bit file
I attached a picture. Don't remember if that can be done.
This is the config I need but I will be damned if I can get PnCConf
to do this. Maybe I dont understand the GUI where the pin
allocations happen that well. If only they would show the I/O
number correctly somewhere. There are some numbers on the left side
but they make no sense.
The pinout is determined by the firmware so many
parallel port type 7I92 bitfiles will do
For example 7i92_5ABOBx2D.bit firmware will work here
You associate stepgen numbers to Axis in pncconf
The firmware maps those numbered stepgens to
physical pins
XSTEP - 2 : XDIR -3
X2STEP - 4 : X2DIR - 5
YSTEP - 6 : YDIR - 7
NO Z (or 16 and 17)
ASTEP - 8 : ADIR 9
On 2022/04/12 15:50, andy pugh wrote:
On Tue, 12 Apr 2022 at 13:48, Marius <mar...@mastercut.co.za> wrote:
The config I have to replicate is this.
Seems to be coming through blank.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users