So this morning I whipped up a small g-code program to test the tapping. I started a fresh LinuxCNC so that most of the parameters were default. Did a HOME command and then moved to the logical home position with a G0 X0 Y0 G0 Z0. Then loaded this program.
G17 G20 G40 G90 G1 X0 Y0 F20 G1 Z0 S200 M3 G33.1 Z-0.7 K0.05 I3.0 g0 Z0.5 M5 M2 % The program loaded without errors. What's interesting is that this time although the knee went back down at 3x the speed after tapping the end result was a "Joint 2 following error" Remove the I3.0 and the following error does not happen. Works with I1.5 but not I2.0. Not sure why that is. It worked the other day, even from the MDI entry with I3.0. And now it also generates the following error from the MDI. I'm going to guess either the machine is cold and a bit stiff or there were some other parameters the other day set that prevented the fault. In either case, I do not get a fault loading the program. John -----Original Message----- From: Nicklas SB Karlsson [mailto:n...@nksb.eu] Sent: June 28, 2023 6:30 AM To: emc-users@lists.sourceforge.net Subject: Re: [Emc-users] G33.1 error then g-code file parsed Have used the latest origin/master not more than a few weeks old but have not checked against older version. Will do this sooner or later, hopefully within a week. Den 2023-06-26 kl. 07:29, skrev John Dammeyer: > OK. > I'll try that for you. > I'm wondering if perhaps spindle acceleration time or some other HAL > parameter gets flagged with an incorrect error message. I've done power > tapping from .ngc files without issue but I've not used the 'I' parameter. > John > > -----Original Message----- > From: Nicklas SB Karlsson [mailto:n...@nksb.eu] > Sent: June 25, 2023 10:09 PM > To: emc-users@lists.sourceforge.net > Subject: Re: [Emc-users] G33.1 error then g-code file parsed > > Run from MDI then there is no error message for me either. Put the same > rows in a .ngc file adding M2 and bottom there is an interpreter error > message then loading the file and display not updated. Looking at bottom > the program is however actually loaded and seems to work OK. > > > Nicklas Karlsson > > > Den 2023-06-26 kl. 01:26, skrev John Dammeyer: >> I ran the following commands from the MDI without issue from AXIS 2.8.1 > with >> MESA 7i92H controlling an AC Servo motor (step/dir) for the spindle. >> G1 X0 Y0 F20 >> G1 Z0 >> S200 M3 >> G33.1 Z-0.7 K0.05 I3.0 >> M5 >> >> Interesting watching the spindle RPM indicator, and you can hear it too of >> course. >> Goes down to tap the 0.05" pitch (20TPI thread) at 200RPM >> Reverses and goes up at 600 RPM. >> Without the I3.0 it goes up at 200 RPM. >> >> John >> >> >> -----Original Message----- >> From: Nicklas SB Karlsson [mailto:n...@nksb.eu] >> Sent: June 25, 2023 9:07 AM >> To: emc-users@lists.sourceforge.net >> Subject: Re: [Emc-users] G33.1 error then g-code file parsed >> >> There is positioning move XYZ in real program but happened to remove >> them then I should make a small test case. >> >> Adding positioning move to test case make no difference. Linuxcnc report >> a file interpretation error and do not update display but program seems >> to work supposed to. >> >> Nicklas Karlsson >> >> >> Den 2023-06-23 kl. 16:20, skrev Chris Radek: >>> I would add positioning moves (positioning all of XYZ) before the >>> G33.1 because otherwise the tapped hole can be anywhere - the >>> program is indeterminate. This sure might mess up any attempt by >>> your GUI to check the program or generate a preview. >>> >>> Chris >>> >>> On Wed, Jun 14, 2023 at 09:14:20PM +0200, Nicklas SB Karlsson wrote: >>>> I put the lines below into a file: >>>> >>>> ?? M3 S100 >>>> ?? G33.1 Z-30.474 K0.8 I3.000 >>>> ?? M5 >>>> ?? M2 >>>> >>>> Then I read into Linuxcnc I get error message: >>>> >>>> ?? parse_file interp_error >>>> >>>> Removing the line with G33.1 then no error message so it is something >>>> with this row. Program do however execute as expected with G33.1 line >>>> even though there is an error message so no real problem. Also execute >>>> without an error message if run manually in MDI mode. Use origin/master >>>> last commit Mon May 8 16:10:03 2023 +0200 >>>> 404aa407f136ce91a3e6bf911c7bda54011a74e9 Anybody else had similar >> problem? >>>> Nicklas Karlsson >>>> >>>> >>>> >>>> _______________________________________________ >>>> Emc-users mailing list >>>> Emc-users@lists.sourceforge.net >>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>> >>> _______________________________________________ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> >> >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
