If I type python from the command line I get 2.7.13. If I type python3 I get python 3.5.
-----Original Message----- From: Nicklas SB Karlsson [mailto:n...@nksb.eu] Sent: July 3, 2023 3:46 PM To: emc-users@lists.sourceforge.net Subject: Re: [Emc-users] G33.1 error then g-code file parsed Trying 2.9 it did not here. Same problem with master. Checking out 2.8 and compiling it complain python is not found. If I remember correct there have been change of python version. You use 2.8 or older? Nicklas Karlsson Den 2023-06-28 kl. 19:52, skrev John Dammeyer: > So this morning I whipped up a small g-code program to test the tapping. I > started a fresh LinuxCNC so that most of the parameters were default. > Did a HOME command and then moved to the logical home position with a G0 X0 > Y0 G0 Z0. > Then loaded this program. > > G17 G20 G40 G90 > G1 X0 Y0 F20 > G1 Z0 > S200 M3 > G33.1 Z-0.7 K0.05 I3.0 > g0 Z0.5 > M5 > M2 > % > > The program loaded without errors. > What's interesting is that this time although the knee went back down at 3x > the speed after tapping the end result was a "Joint 2 following error" > Remove the I3.0 and the following error does not happen. Works with I1.5 > but not I2.0. > > Not sure why that is. It worked the other day, even from the MDI entry with > I3.0. And now it also generates the following error from the MDI. > > I'm going to guess either the machine is cold and a bit stiff or there were > some other parameters the other day set that prevented the fault. > In either case, I do not get a fault loading the program. > > John > > > -----Original Message----- > From: Nicklas SB Karlsson [mailto:n...@nksb.eu] > Sent: June 28, 2023 6:30 AM > To: emc-users@lists.sourceforge.net > Subject: Re: [Emc-users] G33.1 error then g-code file parsed > > Have used the latest origin/master not more than a few weeks old but > have not checked against older version. Will do this sooner or later, > hopefully within a week. > > > Den 2023-06-26 kl. 07:29, skrev John Dammeyer: >> OK. >> I'll try that for you. >> I'm wondering if perhaps spindle acceleration time or some other HAL >> parameter gets flagged with an incorrect error message. I've done power >> tapping from .ngc files without issue but I've not used the 'I' parameter. >> John >> >> -----Original Message----- >> From: Nicklas SB Karlsson [mailto:n...@nksb.eu] >> Sent: June 25, 2023 10:09 PM >> To: emc-users@lists.sourceforge.net >> Subject: Re: [Emc-users] G33.1 error then g-code file parsed >> >> Run from MDI then there is no error message for me either. Put the same >> rows in a .ngc file adding M2 and bottom there is an interpreter error >> message then loading the file and display not updated. Looking at bottom >> the program is however actually loaded and seems to work OK. >> >> >> Nicklas Karlsson >> >> >> Den 2023-06-26 kl. 01:26, skrev John Dammeyer: >>> I ran the following commands from the MDI without issue from AXIS 2.8.1 >> with >>> MESA 7i92H controlling an AC Servo motor (step/dir) for the spindle. >>> G1 X0 Y0 F20 >>> G1 Z0 >>> S200 M3 >>> G33.1 Z-0.7 K0.05 I3.0 >>> M5 >>> >>> Interesting watching the spindle RPM indicator, and you can hear it too > of >>> course. >>> Goes down to tap the 0.05" pitch (20TPI thread) at 200RPM >>> Reverses and goes up at 600 RPM. >>> Without the I3.0 it goes up at 200 RPM. >>> >>> John >>> >>> >>> -----Original Message----- >>> From: Nicklas SB Karlsson [mailto:n...@nksb.eu] >>> Sent: June 25, 2023 9:07 AM >>> To: emc-users@lists.sourceforge.net >>> Subject: Re: [Emc-users] G33.1 error then g-code file parsed >>> >>> There is positioning move XYZ in real program but happened to remove >>> them then I should make a small test case. >>> >>> Adding positioning move to test case make no difference. Linuxcnc report >>> a file interpretation error and do not update display but program seems >>> to work supposed to. >>> >>> Nicklas Karlsson >>> >>> >>> Den 2023-06-23 kl. 16:20, skrev Chris Radek: >>>> I would add positioning moves (positioning all of XYZ) before the >>>> G33.1 because otherwise the tapped hole can be anywhere - the >>>> program is indeterminate. This sure might mess up any attempt by >>>> your GUI to check the program or generate a preview. >>>> >>>> Chris >>>> >>>> On Wed, Jun 14, 2023 at 09:14:20PM +0200, Nicklas SB Karlsson wrote: >>>>> I put the lines below into a file: >>>>> >>>>> ?? M3 S100 >>>>> ?? G33.1 Z-30.474 K0.8 I3.000 >>>>> ?? M5 >>>>> ?? M2 >>>>> >>>>> Then I read into Linuxcnc I get error message: >>>>> >>>>> ?? parse_file interp_error >>>>> >>>>> Removing the line with G33.1 then no error message so it is something >>>>> with this row. Program do however execute as expected with G33.1 line >>>>> even though there is an error message so no real problem. Also execute >>>>> without an error message if run manually in MDI mode. Use origin/master >>>>> last commit Mon May 8 16:10:03 2023 +0200 >>>>> 404aa407f136ce91a3e6bf911c7bda54011a74e9 Anybody else had similar >>> problem? >>>>> Nicklas Karlsson >>>>> >>>>> >>>>> >>>>> _______________________________________________ >>>>> Emc-users mailing list >>>>> Emc-users@lists.sourceforge.net >>>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>>> >>>> _______________________________________________ >>>> Emc-users mailing list >>>> Emc-users@lists.sourceforge.net >>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>> _______________________________________________ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >>> >>> >>> >>> _______________________________________________ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> >> >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
