I had the equivalent for my BeagleBone Black which used the co-processor to 
create the step/dir and ran a version of LinuxCNC called MachineKit.  The only 
thing wrong with the board was that it used NO switches for limit etc.  Very 
dangerous.  I did actually run my mill with it for a short time.  However 
Xylotex appears to be gone as is MachineKit.

> -----Original Message-----
> From: Sam Sokolik [mailto:[email protected]]
> Sent: November 9, 2026 11:19 AM
> To: Enhanced Machine Controller (EMC)
> Subject: Re: [Emc-users] raspberry pi and parallel port
> 
> I would second mesa hardware...  But..
> 
> I have one of these and it works 'ok'
> 
> You are pretty limited in step output speed
> 
> https://byte2bot.com/products/parallel-port-raspberry-pi-hat
> 
> In his configs - the base thread is 150000ns - which without reset
> functionality (I don't know if the gpio in the rpi allows for that) is
> 3.3khz.
> 
> But certainly usable for some things..
> 
> sam
> 
> On Mon, Nov 9, 2026 at 11:30�AM andy pugh <[email protected]>
> wrote:
> 
> > On Mon, 9 Nov 2026 at 01:08, fxkl47BF--- via Emc-users
> > <[email protected]> wrote:
> > >
> > > i have a small cnc router that is driven by the parallel port of a pc
> > > i see at "https://www.linuxcnc.org/docs/html/drivers/hal_pi_gpio.html";
> > that i can use the gpio pins of a raspberry pi for this
> > > is anyone doing this and can you share what you learned
> >
> > There should be enough pins to replace a parallel port, however you
> > might have trouble with voltage levels.
> > Does your equipment work properly with 3.3V signals? And are any
> > inputs to the Pi at a safe voltage for the Pi? (switches and even
> > Proximity sensors can switch-to-gnd so are not a problem there)
> >
> > I hesitate to recommend them, as PCW has a living to make, but there
> > are some cheap clones of the "7i92" board on AliExpress. None of them
> > bear any real similarity to a real 7i92, so I am unsure why they
> > picked that designation.
> > I recently bought one to see what they were like, and to be fair it's
> > quite nice, with a DIN-rail mounting case and two ethernet sockets for
> > smart-serial expansion boards.
> > The only real drawback over a real Mesa board is that the
> > documentation is terrible, support is likely to be nonexistent and for
> > some reason it insists on two separate 24V supplies, yet all GPIO is
> > 5V.
> >
> > The one that I got was this one:
> > https://www.aliexpress.com/item/1005010164851154.html
> > As is always the case with AliExpress, you have to look beyond the
> > headline price and factor in shipping. And bear in mind that as
> > someone else observed "it is like buying stuff from raccoons that have
> > no idea what anything is for or what it should cost"
> >
> >
> > --
> > atp
> > "A motorcycle is a bicycle with a pandemonium attachment and is
> > designed for the especial use of mechanical geniuses, daredevils and
> > lunatics."
> > � George Fitch, Atlanta Constitution Newspaper, 1912
> >
> >
> > _______________________________________________
> > Emc-users mailing list
> > [email protected]
> > https://lists.sourceforge.net/lists/listinfo/emc-users
> >
> 
> _______________________________________________
> Emc-users mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/emc-users
_______________________________________________
Emc-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/emc-users

Reply via email to