Yes I did. I'm running kernel 2.2.14, and the card is a Linksys "Network
Everywhere" Fast Ethernet 10/100 NIC Model NC100. I'm going to be opening
the box today to get the exact chipset on the card, but the error messages
in the compile output seem to indicate a library or kernel mismatch... I
was hoping someone had run into this same situation.
John Helmuth
At 11:58 PM 4/13/00 , Sridhar Govindarajulu wrote:
>John,
>
>Did u follow the instructions at the end of the tulip.c file to compile the
>file.
>
>Sridhar
>
>----- Original Message -----
>From: "John Helmuth" <[EMAIL PROTECTED]>
>To: <[EMAIL PROTECTED]>
>Cc: <[EMAIL PROTECTED]>
>Sent: Thursday, April 13, 2000 10:59 PM
>Subject: Re: [expert] Tulip NIC problem
>
>
>> What version of the kernel were you running? When I try to compile the
>> stuff I downloaded from the site referenced in the readme on the diskette,
>> I get a ton of linking errors. Here's the top of the output from the gcc
>> command:
>>
>> In file included from /usr/include/linux/fs.h:270,
>> from /usr/include/linux/capability.h:13,
>> from /usr/include/linux/binfmts.h:5,
>> from /usr/include/linux/sched.h:8,
>> from tulip.c:128:
>> /usr/include/linux/hpfs_fs_i.h:5: parse error before `ino_t'
>> /usr/include/linux/hpfs_fs_i.h:5: warning: no semicolon at end of struct
>or
>> union
>> /usr/include/linux/hpfs_fs_i.h:12: parse error before `:'
>> In file included from /usr/include/linux/fs.h:272,
>> from /usr/include/linux/capability.h:13,
>> from /usr/include/linux/binfmts.h:5,
>> from /usr/include/linux/sched.h:8,
>> from tulip.c:128:
>>
>> Thanks for any help on this prob,
>>
>> John Helmuth
>>
>> At 06:31 PM 4/7/00 , Sridhar Govindarajulu wrote:
>> >I recently installed a linksys fast ehternet 10/100 card on my system. I
>had
>> >to use compile the driver(tulip.c) from the diskette to make my card
>work. I
>> >configured as a module.
>> >
>> >Sridhar
>> >
>> >----- Original Message -----
>> >From: "Jayson S Baird" <[EMAIL PROTECTED]>
>> >To: <[EMAIL PROTECTED]>
>> >Sent: Friday, April 07, 2000 12:33 PM
>> >Subject: [expert] Tulip NIC problem
>> >
>> >
>> >> When using Mandrake 7.0 after install, it fails to access the
>> >> network. ifconfig reads that my mask, IP and broadcast addresses are
>> >> correct and my default route is set correctly through route. The light
>on
>> >> my hub fails to light up though. My card works in RedHat 6-6.2 and just
>> >> for some reason doesn't want to work in Mandrake. DrakX successfully
>found
>> >> my card and in bootup it says it is starting up eth0. Any ideas on how
>to
>> >> remedy this problem?
>> >>
>> >> Jay
>> >>
>> >> Jayson Baird - Kansas State University ==== CNS UNIX Administrator
>> >> "My only skill as a programmer is twisted cleverness..'Click mouse to
>> >> continue *click* release to detonate.'"
>> >>
>> >>
>> >
>>
>> __________________________________________________
>> Do You Yahoo!?
>> Talk to your friends online with Yahoo! Messenger.
>> http://im.yahoo.com
>>
>>
>
__________________________________________________
Do You Yahoo!?
Talk to your friends online with Yahoo! Messenger.
http://im.yahoo.com
