Hi, I had the same problem, try to go in the controlcenter and then information -> sound. Check the I/O, IRQ, DMA ..... Set the right values depends on your card. Thomas Am Die, 21 Nov 2000 schrieben Sie: > > Hello Wayne, > > I have also a sever problem with sound in my fresh install of LM 7.2 - I just > have no sound whatsoever. > I tried to get into DiskDrake and my Sound Blaster 16 card is detected allright, > but when I run the configuration tool it justs answers like you saw : > _initmodule : Device or ressource busy > Everything was working fine under LM 7.1 before... > What could be wrong ? > > En r�ponse � Wayne Wilson <[EMAIL PROTECTED]>: > > > I just did a re-install of 7.2 on my freshly re-formatted drives (which > > used to have 7.1 on them, but the upgrade left a big mess). I still > > have assorted problems which didn't exist in 7.1. > > > > Sound is very annoying. It clicks and pops when effects are played. > > When playing CD's it is distorted and sometimes just drops out > > altogether. I was hoping a clean install would fix things, but no > > luck. Here is the error I get on startup: > > > > kernel: isapnp: Card 'CS4236B' > > kernel: isapnp: 1 Plug & Play card detected total > > kernel: ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen > > 1993-1996 > > kernel: cs4232: dma, dma2, irq and io must be set. > > modprobe: /lib/modules/2.2.17-21mdk/misc/cs4232.o: > > modprobe: Hint: insmod errors can be caused by incorrect module > > parameters, including invalid IO or IRQ parameters > > modprobe: init_module: Device or resource busy > > modprobe: /lib/modules/2.2.17-21mdk/misc/cs4232.o: insmod > > /lib/modules/2.2.17-21mdk/misc/cs4232.o failed > > modprobe: /lib/modules/2.2.17-21mdk/misc/cs4232.o: insmod cs4232 failed > > sound: Loading sound module (cs4232) failed > > > > > > And when doing a insmod after startup from root, I get this: > > insmod cs4232 > > Using /lib/modules/2.2.17-21mdk/misc/cs4232.o > > insmod: a module named cs4232 already exists > > > > > > And then in messages, after startup the following errors are reported: > > modprobe: Can't locate module char-major-4 - maybe not related? > > modprobe: Can't locate module char-major-180 - maybe not related? > > kernel: ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen > > 1993-1996 > > Nov 20 09:32:20 wwilson modprobe: modprobe: Can't locate module > > sound-service-0-3 > > kernel: ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen > > 1993-1996 > > Nov 20 09:50:33 wwilson modprobe: modprobe: Can't locate module > > sound-service-0-3 > > > > And in kernel/errors I found this: > > cs4232: dma, dma2, irq and io must be set. > > > > When I do a lsmod I get this: > > cs4232 2960 0 (autoclean) > > ad1848 16848 0 (autoclean) [cs4232] > > uart401 6384 0 (autoclean) [cs4232] > > sound 58368 0 (autoclean) [cs4232 ad1848 uart401] > > soundlow 464 0 (autoclean) [sound] > > soundcore 2800 5 (autoclean) [sound] > > > > And /etc/modules.conf has this in it: > > > > alias sound-slot-0 cs4232 > > options sound dmabuf=1 > > options sound-slot-0 io=0x530 irq=5 dma=1 dma2=1 mpuio=0x330 mpuirq=-1 > > > > > > Now these setting I verified using HardDrake and running the sound > > configuration program. I can hear things, but lots of loud pops, faint > > and scratchy sound. I have systematically gone through all the setting > > and while many of them work, none work better than these. > > > > > > ---------------------------------------- Content-Type: text/plain; name="message.footer" Content-Transfer-Encoding: 8bit Content-Description: ---------------------------------------- -- Dipl.-Ing. (FH) Thomas Linke; Abt.: VI.21 Bundesanstalt f�r Materialforschung und -pr�fung Unter den Eichen 87 12205 Berlin Telefon : 030/ 81044308 Fax : 030/ 81041627
Keep in touch with http://mandrakeforum.com: Subscribe the "[EMAIL PROTECTED]" mailing list.
