Hello, Well I think I tried everything because under 7.1 I used to go into DrakConf run the configuration tool for sound card and get the same screen asking for IRQ,DMAs, etc... with (like in the present case) DMAs set to 0 ; I coud select values for DMAs and if they weren't right the test sample couldn't be heard. However, now I'm trying to do the same but it just displays a message box with a STOP icon and the OK button and the message I said... no test is done so far. So I guesse something else must be wrong somewhere (modules ??) BTW I am using (I think) Alsa...it must be a standard feature in LM 7.2 ? What do you mean w/ control center (not KDE ?) Thanks anyhow. En r�ponse � "Linke, Thomas" <[EMAIL PROTECTED]>: > Hi, > > I had the same problem, > try to go in the controlcenter and then information -> sound. Check the > I/O, IRQ, DMA ..... Set the right values depends on your card. > > Thomas > > > > Am Die, 21 Nov 2000 schrieben Sie: > > > > Hello Wayne, > > > > I have also a sever problem with sound in my fresh install of LM 7.2 - > I just > > have no sound whatsoever. > > I tried to get into DiskDrake and my Sound Blaster 16 card is detected > allright, > > but when I run the configuration tool it justs answers like you saw : > > _initmodule : Device or ressource busy > > Everything was working fine under LM 7.1 before... > > What could be wrong ? > > > > En r�ponse � Wayne Wilson <[EMAIL PROTECTED]>: > > > > > I just did a re-install of 7.2 on my freshly re-formatted drives > (which > > > used to have 7.1 on them, but the upgrade left a big mess). I still > > > have assorted problems which didn't exist in 7.1. > > > > > > Sound is very annoying. It clicks and pops when effects are > played. > > > When playing CD's it is distorted and sometimes just drops out > > > altogether. I was hoping a clean install would fix things, but no > > > luck. Here is the error I get on startup: > > > > > > kernel: isapnp: Card 'CS4236B' > > > kernel: isapnp: 1 Plug & Play card detected total > > > kernel: ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen > > > 1993-1996 > > > kernel: cs4232: dma, dma2, irq and io must be set. > > > modprobe: /lib/modules/2.2.17-21mdk/misc/cs4232.o: > > > modprobe: Hint: insmod errors can be caused by incorrect module > > > parameters, including invalid IO or IRQ parameters > > > modprobe: init_module: Device or resource busy > > > modprobe: /lib/modules/2.2.17-21mdk/misc/cs4232.o: insmod > > > /lib/modules/2.2.17-21mdk/misc/cs4232.o failed > > > modprobe: /lib/modules/2.2.17-21mdk/misc/cs4232.o: insmod cs4232 > failed > > > sound: Loading sound module (cs4232) failed > > > > > > > > > And when doing a insmod after startup from root, I get this: > > > insmod cs4232 > > > Using /lib/modules/2.2.17-21mdk/misc/cs4232.o > > > insmod: a module named cs4232 already exists > > > > > > > > > And then in messages, after startup the following errors are > reported: > > > modprobe: Can't locate module char-major-4 - maybe not related? > > > modprobe: Can't locate module char-major-180 - maybe not related? > > > kernel: ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen > > > 1993-1996 > > > Nov 20 09:32:20 wwilson modprobe: modprobe: Can't locate module > > > sound-service-0-3 > > > kernel: ad1848/cs4248 codec driver Copyright (C) by Hannu > Savolainen > > > 1993-1996 > > > Nov 20 09:50:33 wwilson modprobe: modprobe: Can't locate module > > > sound-service-0-3 > > > > > > And in kernel/errors I found this: > > > cs4232: dma, dma2, irq and io must be set. > > > > > > When I do a lsmod I get this: > > > cs4232 2960 0 (autoclean) > > > ad1848 16848 0 (autoclean) [cs4232] > > > uart401 6384 0 (autoclean) [cs4232] > > > sound 58368 0 (autoclean) [cs4232 ad1848 > uart401] > > > soundlow 464 0 (autoclean) [sound] > > > soundcore 2800 5 (autoclean) [sound] > > > > > > And /etc/modules.conf has this in it: > > > > > > alias sound-slot-0 cs4232 > > > options sound dmabuf=1 > > > options sound-slot-0 io=0x530 irq=5 dma=1 dma2=1 mpuio=0x330 > mpuirq=-1 > > > > > > > > > Now these setting I verified using HardDrake and running the sound > > > configuration program. I can hear things, but lots of loud pops, > faint > > > and scratchy sound. I have systematically gone through all the > setting > > > and while many of them work, none work better than these. > > > > > > > > > > > > ---------------------------------------- > Content-Type: text/plain; name="message.footer" > Content-Transfer-Encoding: 8bit > Content-Description: > ---------------------------------------- > > -- > > Dipl.-Ing. (FH) Thomas Linke; Abt.: VI.21 > Bundesanstalt f�r Materialforschung und -pr�fung > Unter den Eichen 87 > 12205 Berlin > Telefon : 030/ 81044308 > Fax : 030/ 81041627 > > >
Keep in touch with http://mandrakeforum.com: Subscribe the "[EMAIL PROTECTED]" mailing list.
