Ok. Here is lilo.conf. As you can see I boot from floppy.
[root /mnt/floppy] cat etc/lilo.conf
boot=/dev/fd0
timeout=100
message=/boot/message
prompt
image=/vmlinuz-2.2.18-11mdk
label=linux
root=/dev/sdb2
append=" hdd=ide-scsi"
initrd=/initrd.img
Here is /etc/modules as setup by mandrake setup (install)
[root /etc] cat modules
# /etc/modules: kernel modules to load at boot time.
#
# This file should contain the names of kernel modules that are
# to be loaded at boot time, one per line. Comments begin with
# a `#', and everything on the line after them are ignored.
scsi_hostadapter
scsi_hostadapter1
ide-scsi
ide-floppy
bttv
Here is Dmesg. This is a fresh install, nothing updated. I dont
even think I added any software to it yet. I am not worried about
the isa cards, one is modem (I now have dsl) and my sound card isa
now works after I copied my isapnp.conf from my 7.2 partition.
Thanks for the help in this.
[root /etc] dmesg
Linux version 2.2.18-11mdk ([EMAIL PROTECTED]) (gcc version
egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Sun Feb 11 13:56:50 CET
2001
Detected 451036 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 897.84 BogoMIPS
Memory: 126980k/131008k available (1164k kernel code, 408k reserved, 1720k
data, 128k init, 0k bigmem)
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
Inode hash table entries: 16384 (128k), inode-max: 16376
VFS: Diskquotas version dquot_6.4.0 initialized
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
512K L2 cache (4 way)
CPU: L2 Cache: 512K
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xfb3b0
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 131072 bhash 65536)
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: FUJITSU MPC3064AT, ATA DISK drive
hdb: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
hdc: WDC AC26400B, ATA DISK drive
hdd: CD-RW CRX100E, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: FUJITSU MPC3064AT, 6187MB w/256kB Cache, CHS=788/255/63
hdc: WDC AC26400B, 6149MB w/512kB Cache, CHS=13328/15/63
hdd: ATAPI 24X CD-ROM CD-R/RW drive, 1024kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
hsm personality registered
raid5: measuring checksumming speed
8regs : 774.573 MB/sec
32regs : 411.480 MB/sec
using fastest function: 8regs (774.573 MB/sec)
scsi : 0 hosts.
scsi : detected total.
NET4: Frame Diverter 0.461
md.c: sizeof(mdp_super_t) = 4096
Partition check:
hda: hda1 hda2 < hda5 >
hdc: hdc1 < hdc5 hdc6 hdc7 hdc8 hdc9 hdc10 hdc11 >
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.13)
VFS: Mounted root (ext2 filesystem).
(scsi0) <Adaptec AIC-7850 SCSI host adapter> found at PCI 0/11/0
(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
(scsi0) Cables present (Int-50 YES, Ext-50 YES)
(scsi0) Downloading sequencer code... 415 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<Adaptec AIC-7850 SCSI host adapter>
scsi : 1 host.
(scsi0:0:5:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: WDIGTL Model: ENTERPRISE Rev: 1.91
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 5, lun 0
(scsi0:0:6:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: WDIGTL Model: ENTERPRISE Rev: 1.91
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 6, lun 0
SCSI device sda: hdwr sector= 512 bytes. Sectors= 8515173 [4157 MB] [4.2 GB]
sda: sda1 sda2
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8515173 [4157 MB] [4.2 GB]
sdb: sdb1 sdb2
3c59x.c 15Sep00 Donald Becker and others
http://www.scyld.com/network/vortex.html
divert: allocating divert_blk for eth0
eth0: 3Com 3c905B Cyclone 100baseTx at 0xe400, 00:10:5a:a2:85:25, IRQ 10
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 786d.
MII transceiver found at address 0, status 786d.
Enabling bus-master transmits and whole-frame receives.
autodetecting RAID arrays
autorun ...
... autorun DONE.
Invalid session number or type of track
Checking ReiserFS transaction log (device 08:12) ...
Using r5 hash to sort names
Sponsored by thresholdnetworks.com, emusic.com, bigstorage.com
ReiserFS version 3.5.29
VFS: Mounted root (reiserfs filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 128k freed
Adding Swap: 130748k swap-space (priority -1)
hdb:<3>ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 0
unable to read partition table
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 2 hosts.
Vendor: IOMEGA Model: ZIP 100 Rev: 12.A
Type: Direct-Access ANSI SCSI revision: 00
Detected scsi removable disk sdc at scsi1, channel 0, id 0, lun 0
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
sdc: Write Protect is off
sdc: sdc4
Linux video capture interface: v1.00
i2c: initialized
bttv0: Brooktree Bt878 (rev 2) bus: 0, devfn: 80, irq: 9, memory:
0xea000000.
bttv: 1 Bt8xx card(s) found.
bttv0: Hauppauge eeprom: tuner=Philips FM1236 (2)
bttv0: fader chip: TEA6300
bttv0: model: BT878(Hauppauge new)
hdd: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdd: packet command error: error=0x54
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Invalid field in command packet -- (asc=0x24, ascq=0x00)
The failed "Read Table of Contents" packet command was:
"43 02 00 00 00 00 00 00 04 00 00 00 "
VFS: Disk change detected on device ide1(22,64)
hdd: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdd: packet command error: error=0x54
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Invalid field in command packet -- (asc=0x24, ascq=0x00)
The failed "Read Table of Contents" packet command was:
"43 02 00 00 00 00 00 00 04 00 00 00 "
attempt to access beyond end of device
16:40: rw=0, want=33, limit=2
dev 16:40 blksize=1024 blocknr=32 sector=64 size=1024 count=1
isofs_read_super: bread failed, dev=16:40, iso_blknum=16, block=32
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe0000000
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
SB 4.16 detected OK (220)
<SoundBlaster EMU8000 (RAM512k)>
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
hdd: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdd: packet command error: error=0x54
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Invalid field in command packet -- (asc=0x24, ascq=0x00)
The failed "Read Table of Contents" packet command was:
"43 02 00 00 00 00 00 00 04 00 00 00 "
hdd: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdd: packet command error: error=0x54
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Invalid field in command packet -- (asc=0x24, ascq=0x00)
The failed "Read Table of Contents" packet command was:
"43 02 00 00 00 00 00 00 04 00 00 00 "
attempt to access beyond end of device
16:40: rw=0, want=33, limit=2
dev 16:40 blksize=1024 blocknr=32 sector=64 size=1024 count=1
isofs_read_super: bread failed, dev=16:40, iso_blknum=16, block=32
parport0: PC-style at 0x378 (0x778) [SPP,EPP,ECP,ECPEPP,ECPPS2]
parport0: detected irq 7; use procfs to enable interrupt-driven operation.
parport_probe: failed
parport0: no IEEE-1284 device present.
lp0: using parport0 (polling).
VFS: Disk change detected on device fd(2,0)
Here is /etc/modules.conf (unmodified) with the exception of the
sound stuff at the end. Note *Hauppague Win/TV card still will not
work. I get a black and white screen like three times across the
screen. Oh well another fight, later though........
[root /etc] cat modules.conf
pre-install pcmcia_core service pcmcia start
pre-install plip modprobe parport_pc ; echo 7 > /proc/parport/0/irq
post-install usbkbd modprobe keybdev
post-install usbmouse modprobe mousedev
post-install wacom modprobe evdev
# IrDA over a normal serial port, or a serial port compatible IrDA port
alias tty-ldisc-11 irtty
alias irlan0 irlan
# IrCOMM (for printing, PPP, Minicom etc)
alias char-major-161 ircomm-tty
# To be able to attach some dongles
alias irda-dongle-0 tekram
alias irda-dongle-1 esi
alias irda-dongle-2 actisys
alias irda-dongle-3 actisys
alias irda-dongle-4 girbil
alias irda-dongle-5 litelink
alias irda-dongle-6 airport
alias irda-dongle-7 old_belkin
# To use the NSC driver on a Thinkpad laptop
#options nsc-ircc dongle_id=0x09
#alias irda0 nsc-ircc
#alias irda0 smc-ircc
alias parport_lowlevel parport_pc
alias scsi_hostadapter aic7xxx
alias scsi_hostadapter1 ide-scsi
alias scsi_hostadapter2 ide-scsi
alias block-major-11 scsi_hostadapter
alias eth0 3c59x
alias char-major-81 bttv
alias tvcard0 bttv
alias sound-slot-0 sb
options sound dmabuf=1
options opl3 io=0x388
alias midi awe_wave
post-install awe_wave /bin/sfxload /etc/midi/GU11-ROM.SF2
options sb io=0x220 irq=5 dma=1 dma16=5 mpu_io=0x330
-----Original Message-----
From: Ron Stodden [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, February 21, 2001 9:17 PM
To: [EMAIL PROTECTED]
Subject: Re: [expert] mandrake 8.0b and cdrw
Klar Brian D Contr MSG SICN wrote:
>
> I am sure I put in more than I needed too, but this prob really has me
> stumped now
/etc/modules.conf:
Since you already have a real SCSI host adapter, you should have:
alias scsi-hostadapter <driver module>
Now to add emulated SCSI you possibly should add:
alias scsi-hostadapter1 ide-scsi.
It's worth a try.
"mrroboto kernel: hdb:<3>ide-scsi: hdb: unsupported command in
request queue (0)"
>From your log above it seems that you have set up hdb (not hdd) as
your ide-scsi device. Please show us your complete /etc/lilo.conf
and /etc/modules.conf and dmesg in your reply. Thanks.
--
Regards,
Ron. [au]
