It came back, but this time i managed to trace the little bugger to an enabled Auto Drive in DDUTIL (Other-tab). Disabling this option in DDUTL (that I do not use) was all that that was needed. Guess it was a CAT command that did override the setting in PSDR.
regards Richard 2011/2/19 Tim Ellison <[email protected]> > My pleasure. Nothing is a non-issue. Just varying degrees of “issueness” > J > > > > > > -Tim > > > > *From:* Richard Saue [mailto:[email protected]] > *Sent:* Friday, February 18, 2011 6:30 PM > > *To:* Tim Ellison > *Cc:* [email protected] > *Subject:* Re: [FlexEdge] Announcing PowerSDR(TM) v2.0.19 RC1 Release > Candidate > > > > Yes, I started with a new database. I did never import any database. > > > > After your last reply I did reset that database, and now the PTT Out > setting stays persistent here too. > > > > Thanks for your kind assitance on this (non)issue. > > > > Now back using the great little Flex-1500 on CW! > > > > regards > > LA4SGA Richard > > 2011/2/19 Tim Ellison <[email protected]> > > I cannot reproduce that behavior. > > > > I set PTT out in the Antenna form to enable, change bands and it stays > persistent. > > > > Did you start with a new database (no data imports). > > > > > > -Tim > > > > *From:* Richard Saue [mailto:[email protected]] > *Sent:* Friday, February 18, 2011 6:00 PM > *To:* Tim Ellison > *Cc:* [email protected] > > > *Subject:* Re: [FlexEdge] Announcing PowerSDR(TM) v2.0.19 RC1 Release > Candidate > > > > I have tried both, but It does not matter. The setting goes away as soon as > I change band, e.g : I enable PTT in simple mode on 30 meters; change band > to 20 meter; the setting goes away; change band back to 30 meters, and the > setting is still gone. > > > > I have also tried to edit the databasefile: > > > > <HIDAnt> > > <Key>chkPTTOutEnable</Key> > > <Value>True</Value> > > </HIDAnt> > > > > When I start PowerSDR the PTT setting is enabled. This seting does, > however, also go away as soon as I change band. > > > > 73 de LA4SGA Richard > > > > 2011/2/18 Tim Ellison <[email protected]> > > Are you using the Expert Setting in the Antenna Form? If so you have to > set it for each band. > > > -Tim > > > > -----Original Message----- > From: [email protected] [mailto: > [email protected]] On Behalf Of Richard Saue > Sent: Friday, February 18, 2011 5:41 PM > To: [email protected] > Subject: Re: [FlexEdge] Announcing PowerSDR(TM) v2.0.19 RC1 Release > Candidate > > Hi, > the new version seems like an improvement on cw. > > Using a Flex-1500 I do now have problems enabling PTT Out on flexwire for a > 100w PA. I can enable PTT in the Antenna Section, and it works. But as soon > as I change band, the setting goes away. This was no problem using v2.0.16. > Am I the only one with this problem? > > 73 de LA4SGA Richard > > > > > 2011/2/18 Gerald Youngblood <[email protected]> > > > Dear FlexRadio customers: > > > > > > FlexRadio is pleased to announce the availability of PowerSDR v2.0.19 > > Release Candidate 1 (RC1) for public download from our website. This > > version incorporates a totally new CW keying architecture that was > > written from the ground up to achieve minimum jitter and latency using > > both internal > > and external keyers. To say this is a rewrite is a bit of an > > understatement. We got out Farnsworth and started from "dit." > > Everything is right now in "PARIS." > > > > > > We have also done significant work since the v2.0.16 beta release to > > improve installation and overall out of box experience on all radios. > > We have optimized the USB driver for the FLEX-1500 to perform well on > > a wide range of PC platforms. We have also incorporated a new > > FireWire driver with less CPU overhead on Windows 7 systems. The > > number of little and not so little bug fixes are too numerous to > > mention here. Check out the change log and release notes. A note > > about release notes, PLEASE READ the them to get the most from your > > FlexRadio. > > > > > > The URL for the release notes is: > > > > http://support.flex-radio.com/Downloads.aspx?id=359 > > > > > > > > The URL for the installer software is: > > > > http://support.flex-radio.com/Downloads.aspx?id=358 > > > > > > > > We are very excited about v2.0.19 RC1 as we enter the final steps > > toward the PowerSDR v2.0.x Official Release. We thank you for your > > patience and support while we have been preparing this important > > release. We request you report any bugs found in this release to the > > bug tracker at http://support.flexradio.com/BugList.aspx?it=b. Be > > sure to note 2.0.19 > > RC1 > > in the Software Product Version field as we will be focusing our > > attention on those specific reports. > > > > > > > > We would like to say a special thanks to our beta team for their > > tireless support in testing a number of interim releases to get here. > > > > > > We are taking the weekend off but 2.1 starts on Monday. In the > > software world it is never finished. > > > > > > Warmest 73s, > > > > > > Gerald > > > > > > Gerald Youngblood, K5SDR > > President and CEO > > FlexRadio Systems(TM) > > 13091 Pond Springs Road, #250 > > Austin, TX 78729 > > Phone: 512-535-4713 Ext. 202 > > Email: [email protected] > > Web: www.flexradio.com <http://www.flex-radio.com/> > > > > Tune In Excitement (TM) > > > > PowerSDR(TM) is a trademark of FlexRadio Systems > > _______________________________________________ > > Flexedge mailing list > > [email protected] > > http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz > > This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is > > used for posting topics related to SDR software development and > > experimentalist who are using beta versions of the software. > > > _______________________________________________ > Flexedge mailing list > [email protected] > http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz > This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is used > for posting topics related to SDR software development and experimentalist > who are using beta versions of the software. > > > > > _______________________________________________ Flexedge mailing list [email protected] http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is used for posting topics related to SDR software development and experimentalist who are using beta versions of the software.
