I am getting same problem with NTC sky R-uim card. but its through usb ruim reader...
THe output of wvdialconf command is: r...@notebook-raz:~$ wvdialconf /etc/wvdial.conf Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. Modem Port Scan<*1>: S0 S1 S2 S3 WvModem<*1>: Cannot get information for serial port. ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at http://open.nit.ca/wiki/?WvDial If you still have problems, send mail to <[email protected]>. ---------------------------------------------------------------------------------------------------------------------------------------------------------- On Mon, Dec 8, 2008 at 11:22 PM, Shristi Pradhan <[email protected]>wrote: > > Shishir dai, i am still not being able to connect to net. > I edited my wvdial.conf file using the command "sudo nano /etc/ > wvdial.conf". > I gave all the parameters u specified with my username and password > (the same which i use in windows). > > then i tried with the command "wvdialconf" and "wvdial"....but no > success.. > my output for these commands as follows: > > $ wvdialconf: > > Editing `/etc/wvdial.conf'. > > Scanning your serial ports for a modem. > > WvModem<*1>: Cannot set information for serial port. > ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud > ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud > ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. > Modem Port Scan<*1>: S1 S2 S3 > > Sorry, no modem was detected! Is it in use by another program? > > Did you configure it properly with setserial? > > $ wvdial: > > --> WvDial: Internet dialer version 1.60 > --> Cannot set information for serial port. > --> Initializing modem. > --> Sending: ATZ > --> Sending: ATQ0 > --> Re-Sending: ATZ > --> Modem not responding. > > > Please help me out troubleshooting this problem! .. > am i having some other problems ??? > are there any other alternatives??? > > Regards, > Shristi > > > On Dec 7, 11:11 pm, "Shishir Jha" <[email protected]> wrote: > > Ok shrishti, try doing this, > > put this in your init2 string in your wvdial.conf file. > > > > *at+fclass=0;at+crm=2;at$qcmdr=3;* > > > > Next what you do is, while dialing, pick your handset up, i mean make > sure > > there is a dialtone audible in the handset before you dial. I know this > > sounds funny, but works for me almost always. Just let me know what the > > results are. > > > > So this is how your file should look > > > > [Dialer Defaults] > > Init1 = ATZ > > Init2 =*at+fclass=0;at+crm=2;at$qcmdr=3;* > > New PPPD = yes > > Phone = #777 > > Modem = /dev/ttyS0 > > Username = username > > Password = password > > Baud = 115200 > > > > Cheers. Do reply back with the result > > On Sun, Dec 7, 2008 at 10:10 PM, Shristi Pradhan <[email protected] > >wrote: > > > > > > > > > > > > > > > > > hello, (i am sorry for late response) > > > > > i am sending the output of following commands. Please check it out. > > > > > $ lshw: > > >http://pastebin.com/f475e1e55 > > > > > $ dmesg: > > >http://pastebin.com/f47a454c3 > > > > > $ cd /var/log > > > $ cat messages > > >http://pastebin.com/f109eccaf > > > > > $ wvdialconf > > >http://pastebin.com/f2934fa85 > > > > > I am using CDMA wireless fixed phone (WP 805)..Ya, this is NTC ko CDMA > > > phone.. and my phone is connected through a simple serial cable and > > > not USB cable. > > > I had changed my USB cable after it got damaged so i dont use it > > > anymore and my serial cable works fine (i.e while connecting in > > > windows). > > > > > I would be grateful if someone could help me out soon. :) > > > > > Regards, > > > Shristi Pradhan > > > > > On Dec 1, 7:10 am, "abish adhikari" <[email protected]> wrote: > > > > lets start from the beginning. what does your modem look like? is it > > > > wireless modem or is it the NTC ko CDMA phone . you on a desktop? > > > > > > On 11/30/08, Shristi Pradhan <[email protected]> wrote: > > > > > > > Hi, > > > > > I am still having problem in connecting my CDMA modem for internet > > > > > connection in ubuntu 8.10. > > > > > I tried both the following links: > > > > >http://wiki.ubuntu.org.np/UsingCDMAModem > > > > > abish.wordpress.com/2008/04/18/using-cdma-wireless-modem-in-ubuntu > > > > > > > But my CDMA phone is connected to my computer's COM1 through serial > > > > > cable and not USB cable. > > > > > I have tried the command "wvdialconf" in the terminal but it says > > > > > modem not detected! > > > > > Please somebody give a solution to this .Help!! > > > > > > > Shristi > > > > > > -- > > > > -Abish- Hide quoted text - > > > > > > - Show quoted text - > > > > -- > > Shishir Jha > > EPC 1970,GPO 8975, > > KTM,NEPAL- Hide quoted text - > > > > - Show quoted text - > > > -- Prabin Gautam Open Source Developer prabin AT prabin DOT net DOT np Mob: +९7७9८4१२5९00१ --~--~---------~--~----~------------~-------~--~----~ FOSS Nepal mailing list: [email protected] http://groups.google.com/group/foss-nepal To unsubscribe, e-mail: [email protected] Community website: http://www.fossnepal.org/ -~----------~----~----~----~------~----~------~--~---
