Hi all, I have a working LACP between cisco and ServerIron. Well, dont ask me why I need a specific command on Cisco side, just tried out different combinations and this one worked! After the config on Cisco and Foundry, I can ping between these 2 boxes.
LACP config on Cisco interface Port-channel13 switchport switchport trunk encapsulation dot1q switchport trunk allowed vlan 2 switchport mode trunk interface GigabitEthernet3/1 logging event link-status logging event spanning-tree status logging event bundle-status logging event trunk-status switchport switchport trunk encapsulation dot1q switchport trunk allowed vlan 2 switchport mode trunk channel-group 13 mode active channel-protocol lacp ! interface GigabitEthernet3/2 logging event link-status logging event spanning-tree status logging event bundle-status logging event trunk-status switchport switchport trunk encapsulation dot1q switchport trunk allowed vlan 2 switchport mode trunk channel-group 13 mode active channel-protocol lacp ! interface GigabitEthernet3/3 logging event link-status logging event spanning-tree status logging event bundle-status logging event trunk-status switchport switchport trunk encapsulation dot1q switchport trunk allowed vlan 2 switchport mode trunk channel-group 13 mode active channel-protocol lacp ! interface GigabitEthernet3/4 logging event link-status logging event spanning-tree status logging event bundle-status logging event trunk-status switchport switchport trunk encapsulation dot1q switchport trunk allowed vlan 2 switchport mode trunk channel-group 13 mode active channel-protocol lacp interface Vlan2 ip address 20.1.1.253 255.255.255.0 ============================================= LACP on Foundry ServerIron interface ethernet 2/9 link-aggregate configure key 21000 link-aggregate active ! interface ethernet 2/10 link-aggregate configure key 21000 link-aggregate active ! interface ethernet 2/11 link-aggregate configure key 21000 link-aggregate active ! interface ethernet 2/12 link-aggregate configure key 21000 link-aggregate active ! interface ve 2 ip address 20.1.1.254 255.255.255.0 ! vlan 2 by port tagged ethe 2/9 to 2/12 router-interface ve 2 Nikolay Pavlov <quetzal at zone3000.net> wrote: On Thursday, 13 July 2006 at 19:25:14 +0900, Hiromasa Sekiguchi wrote: > Hi all, > > Thank you for your help. > > I try the following tests. > But all tests is fail... > > 1. add "channel-protocol lacp" command > > -> fail... > > 2. The LACP mode changed active/passive Cisco and Foundry. > > - Cisco is active, Foundry is active > > -> fail... > > - Cisco is active, Foundry is passive > > -> fail... > > - Cisco is passive, Foundry is active > > -> fail... > > I have no more ideas... > > Are there any ideas??? Why don't just use EtherChannel with out LACP or any aggregation protocol? Here is my configuration: CAT4506: interface GigabitEthernet2/3 description Goes to 2/7 of ServerIron 400 switchport access vlan 55 switchport mode access logging event link-status load-interval 30 speed 1000 no qos channel-group 1 mode on ! interface GigabitEthernet2/4 description Goes to 2/8 of ServerIron 400 switchport access vlan 55 switchport mode access logging event link-status load-interval 30 speed 1000 no qos channel-group 1 mode on SI400: trunk switch ethe 2/7 to 2/8 port-name "trunk to cs4506-sw11-NY 2/3-2/4 " ethernet 2/7 It works cool for me =) > > Regards, > Hiromasa > > > Hiromasa Sekiguchi wrote: > > Hi all, > > > > I try chennel connection between Cisco and Foundry. > > > > The host is the following. > > Cisco : cat3750 > > Foundry : FWS4802-PREM > > > > +---------+ gi2/0/1 e49 +--------------+ > > | cat3750 |=====================| FWS4802-PREM | > > +---------+ gi2/0/2 e50 +--------------+ > > > > ### cat3750 ### > > interface gigabitethernet 2/0/1 > > switchport access vlan *** > > switchport mode access > > channel-group 1 mode active > > > > interface gigabitethernet 2/0/2 > > switchport access vlan *** > > switchport mode access > > channel-group 1 mode active > > ### > > > > ### FWS4802-PREM ### > > interface ethernet 49 > > link-aggregate configure key 20000 > > link-aggregate active > > > > interface ethernet 50 > > link-aggregate configure key 20000 > > link-aggregate active > > ### > > > > When gi2/0/1(or e49) was down, gi2/0/2 was flapped. > > It occur about 90 sec later. > > > > Are there any solution? > > > > Please help!!! > > > > _______________________________________________ > > foundry-nsp mailing list > > foundry-nsp at puck.nether.net > > http://puck.nether.net/mailman/listinfo/foundry-nsp > _______________________________________________ > foundry-nsp mailing list > foundry-nsp at puck.nether.net > http://puck.nether.net/mailman/listinfo/foundry-nsp -- ========================================================================= = Best regards, Nikolay Pavlov. <<<------------------------------------ = ========================================================================= _______________________________________________ foundry-nsp mailing list foundry-nsp at puck.nether.net http://puck.nether.net/mailman/listinfo/foundry-nsp --------------------------------- How low will we go? Check out Yahoo! Messenger?s low PC-to-Phone call rates. -------------- next part -------------- An HTML attachment was scrubbed... URL: https://puck.nether.net/pipermail/foundry-nsp/attachments/20060808/6b9a54cb/attachment.html
