I did 'RTFM' and it recommends that you run quotacheck on startup. I was
wondering why this was.
:-p
If RH6.2 doesn't have quota support built in then how come I don't get an
"error: -ERR Could
not set quota stats" when running vsd-vsbatch.pl?
Cheers,
----
Ben Kennish
email | [EMAIL PROTECTED]
----- Original Message -----
From: "Nick Burrett" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Tuesday, April 10, 2001 10:56 AM
Subject: Re: priv_*
> "Ben Kennish" <[EMAIL PROTECTED]> writes:
>
> > Thanks Paul,
> >
> > When you say that quota support is compiled in, are you talking about RH
> > 6.2? If so, someone should tell HOWTOQuotas.txt that it's wrong and
that
> > RH6.2 does have quota support built into kernel.
>
> 6.2 does not have quota support built in.
>
> > I'm running "quotacheck -avug" now (takes ages I know). Do I ALWAYS
need to
> > do "quotacheck -avug" on system startup as it seems to take around 20
mins
> > which means a lot of hanging around when waiting for system to boot!
>
> No. You only do it once. RTFM
>
> > I'll report back once I've finished. Cheers,
> >
> > ----
> > Ben Kennish
> > email | [EMAIL PROTECTED]
> >
> > ----- Original Message -----
> > From: "Pau Marshall" <[EMAIL PROTECTED]>
> > To: <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>
> > Sent: Monday, April 09, 2001 6:28 PM
> > Subject: Re: priv_*
> >
> >
> > > Hi,
> > >
> > > I originally posted this last week for Ben, but sent it from the wrong
> > > address. I thought it still might help some people out.
> > >
> > > Hi Ben,
> > >
> > > Do you have quotas set up properly? I was getting similar results.
Last
> > > week, I posted a message that no one responded to regarding some
quirky
> > > issues with vsdadm, WebAdmin, and VSDClient. I had notice problems
with
> > > Virtual Servers that had more than 12 users. I know it sounded nuts
and
> > > everyone must of thought I had lost my mind. I was starting to think
the
> > > same thing. When I would run some of the priv_* and quota_* commands
vsd
> > > would hang and eventually produce a Read timeout error. When I ran
> > > quotastats from a VS with few users it spit out 0K for everything
accept
> > > the total usage on the bottom. On the VS with more users, quotastats
spit
> > > out 0K for everyone but admin and mail who were set at about 1320k. In
> > > addition, quotastats would crash with a Segmentation fault after the
> > > output. I tried to use setquota to remove the quota, but it wouldn't
work.
> > >
> > > I started thinking that the problem may not have anything to do with
the
> > > number of users and it was a quota problem. After doing some research
on
> > > quota I determined that it was compiled in the kernel, but it was not
> > > enabled in /etc/fstab for any filesystems. Following the directions in
the
> > > FreeVSD Quota HOWTO, I modified the fstab, and rc.sysinit and ran
> > > quotacheck and quotaon. Everything works, (well for the most part). I
> > don't
> > > get The errors or timeouts now.
> > >
> > > Hope this helps.
> > >
> > > Take care,
> > >
> > > Paul
> > >
> > > At 02:52 AM 4/6/01, Ben Kennish wrote:
> > > >Currently having problems with vsdadm and the priv_ commands.
> > > >
> > > >e.g. when I do...
> > > >
> > > >'vsdadm priv_avail localhost vsone'
> > > >
> > > >I just wait and wait nothing happens and so I press CTRL-C. Same
thing
> > with
> > > >"priv_list"
> > > >
> > > >Trying priv_modify with the following...
> > > >
> > > >`vsdadm priv_modify localhost vsone admin +mail` gives unknown user
vsone
> > > >which is weird considering the syntax is listed as...
> > > >`vsdadm priv_modify <host svr> <vs> <user> <+�- priv>`
> > > >
> > > >
> > > >Any ideas as to what might be causing this one?
> > > >
> > > >Thanks,
> > > >
> > > >----
> > > >Ben Kennish
> > > >
> > > >Software Engineer
> > > >Fubra Limited
> > > >
> > > >web | www.fubra.net
> > > >email | [EMAIL PROTECTED]
> > > >phone | +44 (0)870 1222 600
> > > >fax | +44 (0)870 1222 699
> > >
>
