Dear Max, Yes, that works! The scale is vertical now, even though I cannot move it to the right/left of the view.. but it does not matter, better than nothing.
Thanks for the help, I scanned through the View options in the manual, I did not think of looking at the PostProcessing ones as well. As a suggestion, I think that explaining what the “PostProcessing.HorizontalScales = 0” does in the manual is useful to everyone. Best, Marco From: Max Orok [mailto:[email protected]] Sent: woensdag 4 december 2019 20:21 To: Marco Tiberga Cc: [email protected] Subject: Re: [Gmsh] Change position of value scale Maybe try setting PostProcessing.HorizontalScales = 0; ? [image.png] http://gmsh.info/doc/texinfo/gmsh.html#Post_002dprocessing-options-list<https://urldefense.proofpoint.com/v2/url?u=http-3A__gmsh.info_doc_texinfo_gmsh.html-23Post-5F002dprocessing-2Doptions-2Dlist&d=DwMFaQ&c=XYzUhXBD2cD-CornpT4QE19xOJBbRy-TBPLK0X9U2o8&r=xDQrN9dIlh8hsy24roW04-s63YICVLB4nv0g5BCLJug&m=qUtGaLYrjPCKHK3eKYmQv6iMH0TArZJR0a1__z42B84&s=_xFNXVlwRiYdTzkAs9E8_ogFRAdlhy0gKmXVISByvGk&e=> Sincerely, Max On Wed, Dec 4, 2019 at 1:52 PM Marco Tiberga <[email protected]<mailto:[email protected]>> wrote: Dear Gmsh community, Is there a way to change the position of the value scale in any kind of View? I tried with the most recent Gmsh snapshot, but if I go to “View options” -> “Axes” -> “2D axes/value scale position” only the option “manual” seems to actually be able to change the position. I am using the GUI, FYI. However, I cannot obtain what I want. The “Automatic” position is at the bottom-center of the screen and the scale is horizontal. If possible, I would like to have a vertical scale, to the left or right of the view. Thanks a lot for your help, in advance. Best regards, Marco Tiberga PhD candidate Delft University of Technology Faculty of Applied Sciences Radiation Science & Technology Department Mekelweg 15, 2629 JB Delft, The Netherlands E-Mail: [email protected]<mailto:[email protected]> Website: http://www.nera.rst.tudelft.nl/ _______________________________________________ gmsh mailing list [email protected]<mailto:[email protected]> http://onelab.info/mailman/listinfo/gmsh<https://urldefense.proofpoint.com/v2/url?u=http-3A__onelab.info_mailman_listinfo_gmsh&d=DwMFaQ&c=XYzUhXBD2cD-CornpT4QE19xOJBbRy-TBPLK0X9U2o8&r=xDQrN9dIlh8hsy24roW04-s63YICVLB4nv0g5BCLJug&m=qUtGaLYrjPCKHK3eKYmQv6iMH0TArZJR0a1__z42B84&s=vQWj1_NaXq8Ch7hU7drxqMwPffNWdeYRI7WX8ETha4E&e=> -- Max Orok Contractor www.mevex.com<https://urldefense.proofpoint.com/v2/url?u=http-3A__www.mevex.com&d=DwMFaQ&c=XYzUhXBD2cD-CornpT4QE19xOJBbRy-TBPLK0X9U2o8&r=xDQrN9dIlh8hsy24roW04-s63YICVLB4nv0g5BCLJug&m=qUtGaLYrjPCKHK3eKYmQv6iMH0TArZJR0a1__z42B84&s=hEpgsb8iQgb9wNvhzgjRFugwMCBaHL4jtlZd3L8WtSw&e=> [Image removed by sender.]
_______________________________________________ gmsh mailing list [email protected] http://onelab.info/mailman/listinfo/gmsh
