On Thu, 1 Aug 2013 00:23:26 +0530, Robert Hahne <[email protected]> wrote:
>Hello Mark , > > That's exactly what's happening in my system . I checked the logs for > several IPL's in the past and it looks like GPMSERVE is always started in > that 2 second window (even my system shows a delay of 2 seconds between > EZAIN11I and EZD1176I) . After EZD1176I , GPMSERVE starts w/o any issues . > >Regards, >Bob > > Even though TCP/IP is fully initialized at EZB6473I according to the FM (which comes out right before EZAIN11I), for 2 seconds I probably wouldn't spend my time looking into this even on a supported system. Just change the "TCPIP IS UP" verification message or trigger for this task to be EZD1176I and be done with it. Bigger fish to fry.... Mark -- Mark Zelden - Zelden Consulting Services - z/OS, OS/390 and MVS mailto:[email protected] Mark's MVS Utilities: http://www.mzelden.com/mvsutil.html Systems Programming expert at http://expertanswercenter.techtarget.com/ > >> >> On my system I only see about 2 seconds delay between these two >> messages (I checked several systems and they were all 2 seconds): >> >> EZAIN11I ALL TCPIP SERVICES FOR PROC TCPIP ARE AVAILABLE. >> EZD1176I TCPIP HAS SUCCESSFULLY JOINED THE TCP/IP SYSPLEX GROUP EZBTCPCS >> >> Are you saying you always start GPMSERVE in that 2 second window (or >> whatever it >> is on your system)? If you are starting it prior to EZAIN11I, TCPIP is not >> initialized. I looked and my client's automation and starting tasks that >> require TCPIP are triggered after EZAIN11I. >> >> Regards, >> >> Mark >> -- >> Mark Zelden - Zelden Consulting Services - z/OS, OS/390 and MVS >> mailto:[email protected] >> Mark's MVS Utilities: http://www.mzelden.com/mvsutil.html >> Systems Programming expert at http://expertanswercenter.techtarget.com/ >> >> > >> > >> > >> >> > >> >> >> >> I assume you are asking because z/OS 1.11 is EOS and you don't have >> >> an extended support contract with IBM?? >> >> >> >> Return code is "Condition management for MVS could not be initialized" >> >> >> >> Have you tried getting / looking at the LE dump? >> >> >> >> If you are sure OMVS is fully initialized (which I am assuming it is since >> >> you said TCP/IP is fully functional before starting it), it could be >> >> related >> >> to MAXPROCUSER since it is timing related. What UID does it run under? >> >> >> >> You could take the easy way out (since this is an unsupported system) >> >> and just start it later in the IPL to begin with! >> >> >> >> Mark >> >> -- >> >> Mark Zelden - Zelden Consulting Services - z/OS, OS/390 and MVS >> >> mailto:[email protected] >> >> Mark's MVS Utilities: http://www.mzelden.com/mvsutil.html >> >> Systems Programming expert at http://expertanswercenter.techtarget.com/ >> >> >> >> ---------------------------------------------------------------------- >> >> For IBM-MAIN subscribe / signoff / archive access instructions, >> >> send email to [email protected] with the message: INFO IBM-MAIN >> > >> >---------------------------------------------------------------------- >> >For IBM-MAIN subscribe / signoff / archive access instructions, >> >send email to [email protected] with the message: INFO IBM-MAIN >> >> ---------------------------------------------------------------------- >> For IBM-MAIN subscribe / signoff / archive access instructions, >> send email to [email protected] with the message: INFO IBM-MAIN > >---------------------------------------------------------------------- >For IBM-MAIN subscribe / signoff / archive access instructions, >send email to [email protected] with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
