Hello Mark , Sure . I am gonna try that . Thank you very much for your suggestions !
Regards, Bob > > Even though TCP/IP is fully initialized at EZB6473I according to the FM (which > comes out right before EZAIN11I), for 2 seconds I probably wouldn't spend > my time looking into this even on a supported system. Just change the > "TCPIP IS UP" verification message or trigger for this task to be EZD1176I > and be done with it. Bigger fish to fry.... > > Mark > -- > Mark Zelden - Zelden Consulting Services - z/OS, OS/390 and MVS > mailto:[email protected] > Mark's MVS Utilities: http://www.mzelden.com/mvsutil.html > Systems Programming expert at http://expertanswercenter.techtarget.com/ > > > ur > > > >> > >> On my system I only see about 2 seconds delay between these two > >> messages (I checked several systems and they were all 2 seconds): > >> > >> EZAIN11I ALL TCPIP SERVICES FOR PROC TCPIP ARE AVAILABLE. > >> > >> EZD1176I TCPIP HAS SUCCESSFULLY JOINED THE TCP/IP SYSPLEX GROUP EZBTCPCS > >> > >> > >> Are you saying you always start GPMSERVE in that 2 second window (or > >> whatever it > >> is on your system)? If you are starting it prior to EZAIN11I, TCPIP is > >> not > >> initialized. I looked and my client's automation and starting tasks that > >> require TCPIP are triggered after EZAIN11I. > >> > >> Regards, > >> > >> Mark > >> -- > >> Mark Zelden - Zelden Consulting Services - z/OS, OS/390 and MVS > >> mailto:[email protected] > >> Mark's MVS Utilities: http://www.mzelden.com/mvsutil.html > >> Systems Programming expert at http://expertanswercenter.techtarget.com/ > >> > >> > > >> > > >> > > >> >> > > >> >> > >> >> I assume you are asking because z/OS 1.11 is EOS and you don't have > >> >> an extended support contract with IBM?? > >> >> > >> >> Return code is "Condition management for MVS could not be initialized" > >> >> > >> >> Have you tried getting / looking at the LE dump? > >> >> > >> >> If you are sure OMVS is fully initialized (which I am assuming it is > >> >> since > >> >> you said TCP/IP is fully functional before starting it), it could be > >> >> related > >> >> to MAXPROCUSER since it is timing related. What UID does it run under? > >> >> > >> >> You could take the easy way out (since this is an unsupported system) > >> >> and just start it later in the IPL to begin with! > >> >> > >> >> Mark > >> >> -- > >> >> Mark Zelden - Zelden Consulting Services - z/OS, OS/390 and MVS > >> >> mailto:[email protected] > >> >> Mark's MVS Utilities: http://www.mzelden.com/mvsutil.html > >> >> Systems Programming expert at http://expertanswercenter.techtarget.com/ > >> >> > >> >> ---------------------------------------------------------------------- > >> >> For IBM-MAIN subscribe / signoff / archive access instructions, > >> >> send email to [email protected] with the message: INFO IBM-MAIN > >> > > >> >---------------------------------------------------------------------- > >> >For IBM-MAIN subscribe / signoff / archive access instructions, > >> >send email to [email protected] with the message: INFO IBM-MAIN > >> > >> ---------------------------------------------------------------------- > >> For IBM-MAIN subscribe / signoff / archive access instructions, > >> send email to [email protected] with the message: INFO IBM-MAIN > > > >---------------------------------------------------------------------- > >For IBM-MAIN subscribe / signoff / archive access instructions, > >send email to [email protected] with the message: INFO IBM-MAIN > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
