CBPDO the latest z/OS 2.1 SMP/E into you z/OS 1.13. Run the UPGRADE. Continue on.
> -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] > On Behalf Of Mainframe Mainframe > Sent: Wednesday, August 13, 2014 6:08 PM > To: [email protected] > Subject: Re: SMPE UPGRADE ISSUE > > Thanks Jon, > Our systems are in sysplex with different version of z/OS > (in my > case its z/OS 1.13 and z/OS 2.1 ) systems. Currently I am in the process of > installing CICS 5.2 release and we have multiple CICS version in our shop also > global CSI is common for all CICS version present in systems. > > The error, I mentioned before was getting during receiving MCS and HOLD > data for CICS 5.2 using CBPDO order. > Just to cross check, I also run receive latest FIXCAT hold data job and > encountered same issues. > > So, now my queries are > > 1) Why is it necessary to run UPGRADE parameter in issue. > > 2) Even if I run receive Job from z/OS 2.1 with setting boundary of GLobal > zone which is part of common global csi > > //SMPCNTL DD * > SET BDY (GLOBAL) . > UPGRADE. > RECEIVE HOLDDATA . > > then I will not be able to use this CICS global CSI from my z/OS 1.13 systems. > So, another alternative is to run this Job from z/OS 1.13 system and then we > can use in z/OS 2.1 also. > > 3) After receive, do we have to specify UPGRADE option while doing apply and > accept as well or it is only required for receive. > > > > > > On Wed, Aug 13, 2014 at 11:07 PM, Jon Perryman <[email protected]> > wrote: > > > Never permanently add UPGRADE to your JCL. You always want to make the > > decision to upgrade a zone becase it PERMANENTLY upgrades that zone. > > I'll discuss this in terms of z/OS release but it actually tied to the > > SMP/e release/PTF level (not z/OS). Let's say are running 1.12, 1.13 > > and 2.1 z/OS and you want SMP/e to run on all 3 of those versions if > > possible. If you run the UPGRADE from 2.1, then this zone cannot be > > updated from 1.12 or 1.13. If you did the UPGRADE from 1.13, then you > > can't run SMP/e against this zone on your 1.12 system but can run it on 1.13 > & 2.1. > > > > WARNING: Run UPGRADE from the lowest level system because you can't > > back it out after the change. If the receive holddata still fails, > > then try it on the next higher release but remember you can't use > > SMP/e from that system. > > > > WARNING: Permanently adding UPGRADE to your JCL could risk using > SMP/e > > from older systems. You could accidentally running the job on your > > newly installed 2.1 system. > > > > Jon Perryman > > > > > > > > On Wednesday, August 13, 2014 9:35 AM, Mainframe Mainframe < > > [email protected]> wrote: > > > > > > > > > >Thanks for reply. I am basically receiving HOLD data and getting this > > >issue. So, as mentioned in last update, Do I have to just update > > >receive JCL with > > > > > >//SMPCNTL DD * > > > SET BDY (GLOBAL) . > > > UPGRADE. > > > RECEIVE HOLDDATA . > > > > > >above UPGRADE option and it will receive the data.But I am still not > > >clear > > > > > > > ---------------------------------------------------------------------- > > For IBM-MAIN subscribe / signoff / archive access instructions, send > > email to [email protected] with the message: INFO IBM-MAIN > > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, send email to > [email protected] with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
