Hi Bob,
I can not even get into the SAL screen. How do you get into the SAL
screen if you do not have a console?
Thanks for the help!
//Thank You,//
//Terry Martin////
//Lockheed Martin - Information Technology////
//z/OS & z/VM Systems - Performance and Tuning////
//Cell - 443 632-4191////
//Work - 410 786-0386////
/[EMAIL PROTECTED]///
------------------------------------------------------------------------
*From:* The IBM z/VM Operating System [mailto:[EMAIL PROTECTED]
*On Behalf Of *Hodge, Robert L
*Sent:* Friday, September 12, 2008 5:05 PM
*To:* [email protected]
*Subject:* Re: WAIT STATE
Terry,
From the SAL screen, there is a PF key to list the files on the CP
parm disk. It may help you in determining what went wrong. If you made
a backup of the SYSTEM CONFIG on the parm disk, then you can use the
FN= and FT= options in the IPL parameters area to point to another
SYSTEM CONFIG. If you have another CP parm disk (i.e. 2 or 3) that
would work, then there is field in the upper left of the SAL screen
where you can point to another CP parm disk. Press enter on the SAL
screen to unprotect the CP parm disk field, and press enter after
entering a new value.
------------------------------------------------------------------------
*From:* The IBM z/VM Operating System [mailto:[EMAIL PROTECTED]
*On Behalf Of *Martin, Terry R. (CMS/CTR) (CTR)
*Sent:* Friday, September 12, 2008 2:49 PM
*To:* [email protected]
*Subject:* Re: WAIT STATE
This not the first time I have had this VM up. I changed the system
config adding page packs and such and might have had a finger check!
//Thank You,//
//Terry Martin////
//Lockheed Martin - Information Technology////
//z/OS & z/VM Systems - Performance and Tuning////
//Cell - 443 632-4191////
//Work - 410 786-0386////
/[EMAIL PROTECTED]/
------------------------------------------------------------------------
*From:* Martin, Terry R. (CMS/CTR) (CTR)
*Sent:* Friday, September 12, 2008 4:44 PM
*To:* 'The IBM z/VM Operating System'
*Subject:* RE: WAIT STATE
Hi
Yes, I found this explanation. I think I might have messed up my
system config file which is what is causing this. Can I go into SAPL
mode and enter the cons to get me back in the system if the system
config is in fact corrupted?
//Thank You,//
//Terry Martin////
//Lockheed Martin - Information Technology////
//z/OS & z/VM Systems - Performance and Tuning////
//Cell - 443 632-4191////
//Work - 410 786-0386////
/[EMAIL PROTECTED]/
------------------------------------------------------------------------
*From:* The IBM z/VM Operating System [mailto:[EMAIL PROTECTED]
*On Behalf Of *Doug Breneman
*Sent:* Friday, September 12, 2008 4:36 PM
*To:* [email protected]
*Subject:* Re: WAIT STATE
HCP1010W NO CONSOLE AVAILABLE.
Explanation: The indicated disabled wait state PSW is loaded when an
operational primary or alternate operator's console cannot be found.
If you were running in virtual mode, CONMODE was not set to 3270.
System Action: The system enters a disabled wait state (wait state code =
1010). If using the Stand-Alone Program Loader (SAPL), all registers
contain
the values held at the time the wait state was entered. Register 2
contains
the console device address.
Operator Response: There is probably a hardware malfunction. Notify your
system support personnel. Verify that the RIOGEN macro instruction
properly
defined the primary and alternate system consoles.
If you were running in virtual mode, enter the TERMinal CONMODE 3270
command,
and re-IPL.
If using SAPL, either specify the correct console address on the LOADPARM
parameter of the IPL command or specify the correct console address
using the
'CONS=' IPL parameter on the SAPL menu screen. Refer to Overriding
Stand-Alone
Program Loader Defaults in z/VM: CP Planning and Administration.
If the problem persists, contact your IBM Support Center personnel to
diagnose
and correct the hardware error.
Doug Breneman z/VM Development IBM Endicott
Inactive hide details for "Martin, Terry R. (CMS---09/12/2008 04:27:55
PM---Hi"Martin, Terry R. (CMS---09/12/2008 04:27:55 PM---Hi
From:
"Martin, Terry R. (CMS/CTR) (CTR)" <[EMAIL PROTECTED]>
To:
[email protected]
Date:
09/12/2008 04:27 PM
Subject:
WAIT STATE
------------------------------------------------------------------------
Hi
I am trying to bring up a new VM LPAR and I am receiving a DISABLED
WAIT STATE CODE: 1010.
Any ideas?
/Thank You,/
/Terry Martin/
/Lockheed Martin - Information Technology/
/z/OS & z/VM Systems - Performance and Tuning/
/Cell - 443 632-4191/
/Work - 410 786-0386/
/[EMAIL PROTECTED]/ <mailto:[EMAIL PROTECTED]>
