George,
we do the define and the grant in the System Config
DEFINE VSWITCH VM2SWTCH RDEV 720 730 VLAN 240 PORTT ACCESS NAT 1,
PORTNAME PORT720 PORT730
MODIFY VSWITCH VM2SWTCH GRANT TCPIP
MODIFY VSWITCH VM2SWTCH GRANT MLXESS1T
MODIFY VSWITCH VM2SWTCH GRANT MLXORA1T
and then bring up the controllers and tcpip in the autolog1 profile exec
'CP XAUTOLOG DTCVSW1'
'CP XAUTOLOG DTCVSW2'
'CP SLEEP 30 SEC'
'CP XAUTOLOG TCPIP'
'CP SLEEP 90 SEC'
'CP XAUTOLOG GCS'
munson
From: George Henke/NYLIC <[email protected]>
To: [email protected]
Date: 11/01/2010 03:18 PM
Subject: Re: No IPL VSWITCH Connectivity
Sent by: The IBM z/VM Operating System <[email protected]>
I just noticed that in my AUTOLOG1 PROFILE EXEC, TCPIP is XAUTOLOGed just
before the GRANTS.
Could it be that VSWITCH is not ready until TCPIP is fully logged on, the
TCPIP stack built?
Do I need a delay in my AUTLOG1 PROFILE EXEC after the XAUTOLOG of TCPIP
to make this happen?
'CP XAUTOLOG TCPIP'
'CP SET VSWITCH LNXVSW1 GRANT VLINUX1'
'CP SET VSWITCH LNXVSW1 GRANT VLINUX2'
'CP SET VSWITCH LNXVSW1 GRANT VLINUX3'
'CP SET VSWITCH LNXVSW1 GRANT VLINUX4'
'CP SET VSWITCH LNXVSW1 GRANT VLINUX5'
'CP SLEEP 10 SEC'
'CP XAUTOLOG VLINUX1'
'CP XAUTOLOG VLINUX2'
'CP XAUTOLOG VLINUX3'
Mark Pace <[email protected]>
Sent by: The IBM z/VM Operating System <[email protected]>
11/01/2010 03:13 PM
Please respond to
The IBM z/VM Operating System <[email protected]>
To
[email protected]
cc
Subject
Re: No IPL VSWITCH Connectivity
The 2 entries I have in my system config. 1 for layer 2 and 1 for layer
3. Both work at IPL.
DEFINE VSWITCH VSWTCH1 RDEV 0600 CONTR * ETH
Define VSWITCH VSWTCH3 RDEV 0604 CONTR * IP
On Mon, Nov 1, 2010 at 3:07 PM, George Henke/NYLIC <
[email protected]> wrote:
After IPL we can destroy the VSWITCH:
det vswitch lnxvsw1
Then issue the same commands as in the IPL below and everything connects.
Why?
Are there some restrictions, considerations, for defining the VSWITCH at
IPL time?
SYSTEM CONFIG:
define vswitch lnxvsw1 portname lnxvsw1 rdev 9004
AUTOLOG1: PROFILE EXEC:
'CP SET VSWITCH LNXVSW1 GRANT VLINUX1'
'CP SET VSWITCH LNXVSW1 GRANT VLINUX2'
'CP SET VSWITCH LNXVSW1 GRANT VLINUX3'
'CP SET VSWITCH LNXVSW1 GRANT VLINUX4'
'CP SET VSWITCH LNXVSW1 GRANT VLINUX5'
'CP SLEEP 10 SEC'
'CP XAUTOLOG VLINUX1'
'CP XAUTOLOG VLINUX2'
'CP XAUTOLOG VLINUX3'
--
Mark D Pace
Senior Systems Engineer
Mainline Information Systems
*************************** IMPORTANT
NOTE*****************************-- The opinions expressed in this
message and/or any attachments are those of the author and not
necessarily those of Brown Brothers Harriman & Co., its
subsidiaries and affiliates ("BBH"). There is no guarantee that
this message is either private or confidential, and it may have
been altered by unauthorized sources without your or our knowledge.
Nothing in the message is capable or intended to create any legally
binding obligations on either party and it is not intended to
provide legal advice. BBH accepts no responsibility for loss or
damage from its use, including damage from virus.
********************************************************************************
